合成橡胶工业
閤成橡膠工業
합성상효공업
CHINA SYNTHETIC RUBBER INDUSTRY
2014年
1期
52-56
,共5页
黄舟%刘畅%董彬%吴友平
黃舟%劉暢%董彬%吳友平
황주%류창%동빈%오우평
丁苯橡胶%碳纳米管%疲劳破坏%撕裂能%滞后能
丁苯橡膠%碳納米管%疲勞破壞%撕裂能%滯後能
정분상효%탄납미관%피로파배%시렬능%체후능
styrene-butadiene rubber%carbon nanotube%fatigue failure%tear energy%hysteresis energy
对于炭黑/丁苯橡胶复合材料,分别用1、2和3份(质量,下同)碳纳米管替代4、8和12份炭黑,研究了复合材料在宽应变范围(30% ~ 100%)的抗疲劳破坏性能.结果表明,在30%~70%应变下,与纯炭黑填充的胶料相比,加入碳纳米管疲劳寿命提高,裂纹增长速率降低;在70% ~ 100%应变下,胶料的疲劳寿命降低,裂纹增长速率提高.原因是碳纳米管的加入增大了滞后损失,在小应变下滞后生热可分担部分外界能量,而在大应变下滞后生热增大,使降解加速所致.撕裂能与裂纹增长速率的关系也证明了这一点.此外还证明了采用1份碳纳米管与4份炭黑N 234对丁苯橡胶抗疲劳破坏性能的贡献基本相同.
對于炭黑/丁苯橡膠複閤材料,分彆用1、2和3份(質量,下同)碳納米管替代4、8和12份炭黑,研究瞭複閤材料在寬應變範圍(30% ~ 100%)的抗疲勞破壞性能.結果錶明,在30%~70%應變下,與純炭黑填充的膠料相比,加入碳納米管疲勞壽命提高,裂紋增長速率降低;在70% ~ 100%應變下,膠料的疲勞壽命降低,裂紋增長速率提高.原因是碳納米管的加入增大瞭滯後損失,在小應變下滯後生熱可分擔部分外界能量,而在大應變下滯後生熱增大,使降解加速所緻.撕裂能與裂紋增長速率的關繫也證明瞭這一點.此外還證明瞭採用1份碳納米管與4份炭黑N 234對丁苯橡膠抗疲勞破壞性能的貢獻基本相同.
대우탄흑/정분상효복합재료,분별용1、2화3빈(질량,하동)탄납미관체대4、8화12빈탄흑,연구료복합재료재관응변범위(30% ~ 100%)적항피로파배성능.결과표명,재30%~70%응변하,여순탄흑전충적효료상비,가입탄납미관피로수명제고,렬문증장속솔강저;재70% ~ 100%응변하,효료적피로수명강저,렬문증장속솔제고.원인시탄납미관적가입증대료체후손실,재소응변하체후생열가분담부분외계능량,이재대응변하체후생열증대,사강해가속소치.시렬능여렬문증장속솔적관계야증명료저일점.차외환증명료채용1빈탄납미관여4빈탄흑N 234대정분상효항피로파배성능적공헌기본상동.