大连大学学报
大連大學學報
대련대학학보
JOURNAL OF DALIAN UNIVERSITY
2013年
6期
1-5
,共5页
WN齿轮%动态接触%应力仿真%耦合振动
WN齒輪%動態接觸%應力倣真%耦閤振動
WN치륜%동태접촉%응력방진%우합진동
WN gear%dynamic contact%stress simulation%coupling vibration
基于WN弧齿轮传动特征建立了多自由度切-径-轴及系统误差耦合振动动力学模分析型。利用PROE建立齿轮三维实体模型,通过PROE软件和Ansys软件数据接口将WN弧齿轮三维模型导入Ansys软件中进行了3维冲击动力接触模拟分析,利用施加载荷进行了WN弧齿轮的应力分析,仿真出WN齿轮齿面接触的等效应力云图。在ANSYS/LS-DYNA中构建了齿轮钢柔性体动态接触模型,以用于齿轮转动的动态分析,结果表明WN弧齿轮的切向与轴向方向的振动明显大于径向的振动。
基于WN弧齒輪傳動特徵建立瞭多自由度切-徑-軸及繫統誤差耦閤振動動力學模分析型。利用PROE建立齒輪三維實體模型,通過PROE軟件和Ansys軟件數據接口將WN弧齒輪三維模型導入Ansys軟件中進行瞭3維遲擊動力接觸模擬分析,利用施加載荷進行瞭WN弧齒輪的應力分析,倣真齣WN齒輪齒麵接觸的等效應力雲圖。在ANSYS/LS-DYNA中構建瞭齒輪鋼柔性體動態接觸模型,以用于齒輪轉動的動態分析,結果錶明WN弧齒輪的切嚮與軸嚮方嚮的振動明顯大于徑嚮的振動。
기우WN호치륜전동특정건립료다자유도절-경-축급계통오차우합진동동역학모분석형。이용PROE건립치륜삼유실체모형,통과PROE연건화Ansys연건수거접구장WN호치륜삼유모형도입Ansys연건중진행료3유충격동력접촉모의분석,이용시가재하진행료WN호치륜적응력분석,방진출WN치륜치면접촉적등효응력운도。재ANSYS/LS-DYNA중구건료치륜강유성체동태접촉모형,이용우치륜전동적동태분석,결과표명WN호치륜적절향여축향방향적진동명현대우경향적진동。
Based on double arc gear characteristics and considering system error, a multi-degree-freedom (Tangential-Radial-Axial) coupled vibration dynamics analysis model was established. In this article, we established the three-dimensional solid model by using PROE, imported the arc gear three-dimensional model into Ansys software through the data interface of Ansys software and PROE software and conducted a three-dimensional simulation anasys of the impact of dynamic contact. By applying load, it conducted a stress analysis for double arc gear and gain the double arc gear’s the effective stress clouds. Meanwhile, the rigid-flexible body of gear dynamic contact model based on ANSYS/LS-DYNA was established and the dynamic simulation anasys for WN gear was analyzed. The results demonstrated that the tangential and axial vibration of double arc gear is significantly greater than the radial vibration.