CAJ | 학술논문

为了获得甘蓝根茎部的较佳切割区域和切割要素组合，对甘蓝根茎部进行了切割试验研究。分析了甘蓝根茎部不同直径处的最大切割力、平均切割力、平均含水率和粗纤维含量的分布及相互关系。进行了切割4因素混合水平正交试验，研究了夹持方式、切割方式、切割方向和切割速度对切割力指标的影响。分析结果表明，最大切割力和平均切割力与直径的关系均可用二次多项式拟合，且与粗纤维含量呈线性关系，直径30～35 mm范围为较佳切割区域；夹持方式和切割速度对最大切割力和平均切割力的影响均显著，切割方式仅对最大切割力的影响显著，对平均切割力的影响不显著，切割方向对最大切割力和平均切割力的影响均不显著。较优切割要素组合为单点夹持方式、滑切、向下削切和低速切割。研究结果为甘蓝收获机切割器的设计与改进提供了理论依据。
위료획득감람근경부적교가절할구역화절할요소조합，대감람근경부진행료절할시험연구。분석료감람근경부불동직경처적최대절할력、평균절할력、평균함수솔화조섬유함량적분포급상호관계。진행료절할4인소혼합수평정교시험，연구료협지방식、절할방식、절할방향화절할속도대절할력지표적영향。분석결과표명，최대절할력화평균절할력여직경적관계균가용이차다항식의합，차여조섬유함량정선성관계，직경30～35 mm범위위교가절할구역；협지방식화절할속도대최대절할력화평균절할력적영향균현저，절할방식부대최대절할력적영향현저，대평균절할력적영향불현저，절할방향대최대절할력화평균절할력적영향균불현저。교우절할요소조합위단점협지방식、활절、향하삭절화저속절할。연구결과위감람수획궤절할기적설계여개진제공료이론의거。
Development of a cabbage harvester is an efficient approach to change the traditional way of harvesting cabbage in China. Since cutting is the crucial process, the cutter design is one of the key techniques for the development of cabbage harvester. In order to obtain the best cutting position and cutting combination, taking the cabbage roots as the experimental materials, cutting property tests and chemical composition detection were carried out respectively. The maximum cutting force and average cutting force were taken into consideration as cutting properties. Load-displacement curves on different diameters were sampled depending on the designed test apparatus when the cutting combination was set constantly as two-point support, vertical cutting and the cutting speed of 100 mm/min. The moisture content and crude fiber content, which are the main chemical composition of cabbage root, were measured on the same diameters according to standard process. The relationships between cutting forces and chemical composition were analyzed. The results demonstrated that the maximum cutting force and average cutting force can be fit with the quadratic polynomial of diameters, and F values of the two equations reached to 251.67 and 360.62 respectively and coefficients of determination (R2) were 0.9636 and 0.9743 respectively. Both the curves declined as the cutting diameters increased and got the lowest when the diameters ranged from 30-35 mm which would be the best cutting position. From the space structure of cabbage root, it’s also the most suitable cutting position that is 10-15 mm above the bottom leaves. Multiple linear regression (MLR) was applied to establish the relationships of maximum force, average force with crude fiber content. The results proved that the main factor affecting cutting properties is crude fiber content. Mixed levels orthogonal table (22×32) was utilized to conduct the orthogonal test to obtain the best cutting position considering the factors of support mode, cutting mode, inclining mode and cutting speed which should be determined on the basis of the cabbage harvester designed previously. In the orthogonal test, there were 9 tests and 5 repetitions were conducted for each test. The maximum force and average force were obtained from the load-displacement curves. The orthogonal test results showed that:1) Support mode and cutting speed had significant influences on maximum cutting force and average cutting force, cutting mode had significant influence on maximum cutting force but had no influence on average cutting force, and inclining mode had no influence on maximum cutting force or average cutting force. 2) Based on index minimality of maximum force and average force, the best cutting combination was under the conditions of single point support mode, sliding cutting mode, downward inclining mode and the low cutting speed (50 mm/min). This research can provide a reference for design of the cabbage harvester cutter and optimization of cutting combination.