航空材料学报
航空材料學報
항공재료학보
JOURNAL OF AERONAUTICAL MATERIALS
2013年
6期
57-61
,共5页
张冬娜%寇开昌%张宇%高攀%郑振超
張鼕娜%寇開昌%張宇%高攀%鄭振超
장동나%구개창%장우%고반%정진초
聚四氟乙烯%拉伸%微纤%孔隙%密封
聚四氟乙烯%拉伸%微纖%孔隙%密封
취사불을희%랍신%미섬%공극%밀봉
polytetrafluoroethylene%stretch%fibrils%cavity%seal
针对聚四氟乙烯(PTFE)回弹性差的问题,应用室温单轴拉伸的方法,在相同的拉伸速率下PTFE将试样拉伸至不同长度,以研究拉伸处理对PTFE性能的影响.采用扫描电镜(SEM)观察材料微观形貌,结果表明拉伸处理后PTFE内部出现大量的孔隙与微纤.由于空隙的产生,其密度随着拉伸长度的增加而下降.当拉伸长度为59%时,拉伸强度由未拉伸时的27.34MPa提高至46.90MPa,同时断后伸长率由310%增至410%,邵氏硬度降低.对不同拉伸倍率PTFE的压缩回复性测试可知,随着拉伸长度的增加,PTFE的压缩率由6.74%增加至14.29%,弹性回复率由4.17%增加到6.07%.拉伸处理的PTFE更加适合高性能密封材料.
針對聚四氟乙烯(PTFE)迴彈性差的問題,應用室溫單軸拉伸的方法,在相同的拉伸速率下PTFE將試樣拉伸至不同長度,以研究拉伸處理對PTFE性能的影響.採用掃描電鏡(SEM)觀察材料微觀形貌,結果錶明拉伸處理後PTFE內部齣現大量的孔隙與微纖.由于空隙的產生,其密度隨著拉伸長度的增加而下降.噹拉伸長度為59%時,拉伸彊度由未拉伸時的27.34MPa提高至46.90MPa,同時斷後伸長率由310%增至410%,邵氏硬度降低.對不同拉伸倍率PTFE的壓縮迴複性測試可知,隨著拉伸長度的增加,PTFE的壓縮率由6.74%增加至14.29%,彈性迴複率由4.17%增加到6.07%.拉伸處理的PTFE更加適閤高性能密封材料.
침대취사불을희(PTFE)회탄성차적문제,응용실온단축랍신적방법,재상동적랍신속솔하PTFE장시양랍신지불동장도,이연구랍신처리대PTFE성능적영향.채용소묘전경(SEM)관찰재료미관형모,결과표명랍신처리후PTFE내부출현대량적공극여미섬.유우공극적산생,기밀도수착랍신장도적증가이하강.당랍신장도위59%시,랍신강도유미랍신시적27.34MPa제고지46.90MPa,동시단후신장솔유310%증지410%,소씨경도강저.대불동랍신배솔PTFE적압축회복성측시가지,수착랍신장도적증가,PTFE적압축솔유6.74%증가지14.29%,탄성회복솔유4.17%증가도6.07%.랍신처리적PTFE경가괄합고성능밀봉재료.