新型炭材料
新型炭材料
신형탄재료
NEW CARBON MATERIALS
2012年
5期
393-400
,共8页
梁伊丽%谢志勇%涂川俊%汤贤%杨飘飘%金谷音%黄启忠
樑伊麗%謝誌勇%塗川俊%湯賢%楊飄飄%金穀音%黃啟忠
량이려%사지용%도천준%탕현%양표표%금곡음%황계충
炭纸%石墨粉%电阻率%抗拉强度%透气率
炭紙%石墨粉%電阻率%抗拉彊度%透氣率
탄지%석묵분%전조솔%항랍강도%투기솔
以干法成型技术所制备的聚丙烯腈基炭纤维纸作为炭纸坯体,添加有石墨粉的酚醛树脂溶液作为浸渍剂,通过浸渍、模压固化和热处理工艺制得PEMFC用炭纸.结果表明,随石墨含量的增加,炭纸的厚度、孔隙率逐渐增加,透气性、导电能力逐渐增强,密度和抗拉强度呈先增加后降低的变化规律,当石墨粉质量分数达到5%时炭纸的综合性能最佳,其基本性能参数为:厚度0.23 mm,密度0.53 g·cm-3,气透率2 080 mL· mm· cm-2·h-1·mmAq-1,孔隙率66%,平面电阻率2.6 mΩ· cm-1,拉伸强度19.4 MPa,符合质子交换膜燃料电池气体扩散层对炭纸的要求.采用Pt载量为0.5 mg·cm-2的MEA,在H2/Air=1.2/2.5、温度65℃、常压条件下进行单体电池性能测试,电流密度为800 mA· cm-2时输出电压为0.65 V,电池输出性能较好.
以榦法成型技術所製備的聚丙烯腈基炭纖維紙作為炭紙坯體,添加有石墨粉的酚醛樹脂溶液作為浸漬劑,通過浸漬、模壓固化和熱處理工藝製得PEMFC用炭紙.結果錶明,隨石墨含量的增加,炭紙的厚度、孔隙率逐漸增加,透氣性、導電能力逐漸增彊,密度和抗拉彊度呈先增加後降低的變化規律,噹石墨粉質量分數達到5%時炭紙的綜閤性能最佳,其基本性能參數為:厚度0.23 mm,密度0.53 g·cm-3,氣透率2 080 mL· mm· cm-2·h-1·mmAq-1,孔隙率66%,平麵電阻率2.6 mΩ· cm-1,拉伸彊度19.4 MPa,符閤質子交換膜燃料電池氣體擴散層對炭紙的要求.採用Pt載量為0.5 mg·cm-2的MEA,在H2/Air=1.2/2.5、溫度65℃、常壓條件下進行單體電池性能測試,電流密度為800 mA· cm-2時輸齣電壓為0.65 V,電池輸齣性能較好.
이간법성형기술소제비적취병희정기탄섬유지작위탄지배체,첨가유석묵분적분철수지용액작위침지제,통과침지、모압고화화열처리공예제득PEMFC용탄지.결과표명,수석묵함량적증가,탄지적후도、공극솔축점증가,투기성、도전능력축점증강,밀도화항랍강도정선증가후강저적변화규률,당석묵분질량분수체도5%시탄지적종합성능최가,기기본성능삼수위:후도0.23 mm,밀도0.53 g·cm-3,기투솔2 080 mL· mm· cm-2·h-1·mmAq-1,공극솔66%,평면전조솔2.6 mΩ· cm-1,랍신강도19.4 MPa,부합질자교환막연료전지기체확산층대탄지적요구.채용Pt재량위0.5 mg·cm-2적MEA,재H2/Air=1.2/2.5、온도65℃、상압조건하진행단체전지성능측시,전류밀도위800 mA· cm-2시수출전압위0.65 V,전지수출성능교호.