南水北调与水利科技
南水北調與水利科技
남수북조여수리과기
SOUTH-TO-NORTH WATER
2014年
5期
210-213
,共4页
辛华荣%刘军%董雷%汤正军%徐磊%陆林广
辛華榮%劉軍%董雷%湯正軍%徐磊%陸林廣
신화영%류군%동뢰%탕정군%서뢰%륙림엄
泵站%肘形进水流道%标准化%水力设计%可行性
泵站%肘形進水流道%標準化%水力設計%可行性
빙참%주형진수류도%표준화%수력설계%가행성
pumping station%elbow inlet conduit%standardization%hydraulic design%feasibility
肘形进水流道在大中型立式泵站的应用最为广泛,但在工程实践中对肘形进水流道的水力设计还存在一些问题。通过对采用立式泵装置的南水北调东线一期工程14座新建大型泵站肘形进水流道的控制尺寸进行分析,得到了肘形进水流道控制尺寸取值范围的基本规律,提出以大型泵装置优化水力设计理论为基础,采用 CFD 方法对肘形进水流道进行标准化设计,同时辅之以模型试验的方法进行验证。最后,根据肘形进水流道的优化水力设计实例,对肘形进水流道标准化的要求提出了初步设想。
肘形進水流道在大中型立式泵站的應用最為廣汎,但在工程實踐中對肘形進水流道的水力設計還存在一些問題。通過對採用立式泵裝置的南水北調東線一期工程14座新建大型泵站肘形進水流道的控製呎吋進行分析,得到瞭肘形進水流道控製呎吋取值範圍的基本規律,提齣以大型泵裝置優化水力設計理論為基礎,採用 CFD 方法對肘形進水流道進行標準化設計,同時輔之以模型試驗的方法進行驗證。最後,根據肘形進水流道的優化水力設計實例,對肘形進水流道標準化的要求提齣瞭初步設想。
주형진수류도재대중형입식빙참적응용최위엄범,단재공정실천중대주형진수류도적수력설계환존재일사문제。통과대채용입식빙장치적남수북조동선일기공정14좌신건대형빙참주형진수류도적공제척촌진행분석,득도료주형진수류도공제척촌취치범위적기본규률,제출이대형빙장치우화수력설계이론위기출,채용 CFD 방법대주형진수류도진행표준화설계,동시보지이모형시험적방법진행험증。최후,근거주형진수류도적우화수력설계실례,대주형진수류도표준화적요구제출료초보설상。
Elbow inlet conduit is w idely used in the vertical pump system of the large and medium size pumping stations. H ow ev-er, there are st ill some problems in the engineering practice of hydraulic design for the conduit. Control sizes of the elbow inlet conduit of 14 new ly-built large pumping stations in the first phase of eastern route of South-to-North Water Diversion Project were analyzed, and the basic rules of the control size range were obtained. It is suggested to conduct the standardization design for the elbow inlet conduit using the CFD method based on the t heory of opt imal hydraulic design for the large pump system, and to apply the model test to verif y the result s. Finally, according to an exam ple of the optimum hydraulic design for the elbow inlet conduit , the preliminary assumpt ion on the requirements for the standardization of elbow inlet conduit was proposed.