建筑材料学报
建築材料學報
건축재료학보
JOURNAL OF BUILDING MATERIALS
2012年
6期
760-766
,共7页
碱环境%温度%玻璃纤维增强塑料筋%拉伸性能%预测模型
堿環境%溫度%玻璃纖維增彊塑料觔%拉伸性能%預測模型
감배경%온도%파리섬유증강소료근%랍신성능%예측모형
基于ACI 440.3R-04规定的试验方法,开展了碱环境下玻璃纤维增强塑料(GFRP)筋拉伸性能的加速老化试验研究.试件数量共150根,试验参数包括:(1)碱溶液温度,分别为40,60,80℃;(2)GFRP筋直径,包括12.7,16.0,19.0 mm;(3)碱溶液中的侵蚀时间,分别为3.65,18,36.5,92,183 d.研究表明:在40,60,80℃碱溶液中侵蚀183 d后,直径为16.0 mm的GFRP筋的拉伸强度分别下降了34.97%,48.81%和68.85%;在60℃碱溶液中侵蚀183 d后,12.7,16.0,19.0 mm直径GFRP筋的拉伸强度衰减量分别为56.08%,48.81%和47.08%;随着浸泡时间的增加,40,60,80℃碱环境下GFRP筋的拉伸强度及伸长率呈下降趋势,且温度越高,衰减速率越大.采用扫描电子显微镜(SEM)对腐蚀前后GFRP筋的微观形貌进行了观测,发现腐蚀后GFRP筋的劣化区域内纤维和树脂之间的界面变得松散,纤维与周围树脂之间出现了明显的脱黏现象,而且随着碱环境温度的提高这种脱黏现象变得更为明显.最后,基于Arrhenius方程提出了碱环境下GFRP筋拉伸强度的预测模型.
基于ACI 440.3R-04規定的試驗方法,開展瞭堿環境下玻璃纖維增彊塑料(GFRP)觔拉伸性能的加速老化試驗研究.試件數量共150根,試驗參數包括:(1)堿溶液溫度,分彆為40,60,80℃;(2)GFRP觔直徑,包括12.7,16.0,19.0 mm;(3)堿溶液中的侵蝕時間,分彆為3.65,18,36.5,92,183 d.研究錶明:在40,60,80℃堿溶液中侵蝕183 d後,直徑為16.0 mm的GFRP觔的拉伸彊度分彆下降瞭34.97%,48.81%和68.85%;在60℃堿溶液中侵蝕183 d後,12.7,16.0,19.0 mm直徑GFRP觔的拉伸彊度衰減量分彆為56.08%,48.81%和47.08%;隨著浸泡時間的增加,40,60,80℃堿環境下GFRP觔的拉伸彊度及伸長率呈下降趨勢,且溫度越高,衰減速率越大.採用掃描電子顯微鏡(SEM)對腐蝕前後GFRP觔的微觀形貌進行瞭觀測,髮現腐蝕後GFRP觔的劣化區域內纖維和樹脂之間的界麵變得鬆散,纖維與週圍樹脂之間齣現瞭明顯的脫黏現象,而且隨著堿環境溫度的提高這種脫黏現象變得更為明顯.最後,基于Arrhenius方程提齣瞭堿環境下GFRP觔拉伸彊度的預測模型.
기우ACI 440.3R-04규정적시험방법,개전료감배경하파리섬유증강소료(GFRP)근랍신성능적가속노화시험연구.시건수량공150근,시험삼수포괄:(1)감용액온도,분별위40,60,80℃;(2)GFRP근직경,포괄12.7,16.0,19.0 mm;(3)감용액중적침식시간,분별위3.65,18,36.5,92,183 d.연구표명:재40,60,80℃감용액중침식183 d후,직경위16.0 mm적GFRP근적랍신강도분별하강료34.97%,48.81%화68.85%;재60℃감용액중침식183 d후,12.7,16.0,19.0 mm직경GFRP근적랍신강도쇠감량분별위56.08%,48.81%화47.08%;수착침포시간적증가,40,60,80℃감배경하GFRP근적랍신강도급신장솔정하강추세,차온도월고,쇠감속솔월대.채용소묘전자현미경(SEM)대부식전후GFRP근적미관형모진행료관측,발현부식후GFRP근적열화구역내섬유화수지지간적계면변득송산,섬유여주위수지지간출현료명현적탈점현상,이차수착감배경온도적제고저충탈점현상변득경위명현.최후,기우Arrhenius방정제출료감배경하GFRP근랍신강도적예측모형.