塑料工业
塑料工業
소료공업
CHINA PLASTICS INDUSTRY
2013年
11期
84-86,99
,共4页
尼龙6%缺口曲率半径%缺口深度%缺口尖端应力%断裂伸长率%断裂方式
尼龍6%缺口麯率半徑%缺口深度%缺口尖耑應力%斷裂伸長率%斷裂方式
니룡6%결구곡솔반경%결구심도%결구첨단응력%단렬신장솔%단렬방식
PA6%Notch Root Radius%Notch Depth%Notch Tip Stress%Elongation At Break%Failure Mode
对尼龙6 (PA6)进行不同缺口深度和不同缺口曲率半径的单边缺口拉伸试验,同时采用SEM观察断口形貌.结果表明,随着缺口曲率半径的增加,PA6缺口尖端应力呈逐渐降低,而断裂伸长率呈逐渐上升趋势.缺口曲率半径在0.1~0.5 mm范围内时,拉伸断裂功基本消耗在裂纹萌生阶段,PA6裂纹扩展区表现为脆性断裂方式.当缺口曲率半径大于0.5 mm后,拉伸断裂功主要消耗在裂纹扩展阶段,PA6裂纹扩展区表现为韧性断裂方式.随着缺口深度的增加,缺口附近应力集中程度增大,PA6塑性变形能力下降,缺口尖端应力呈逐渐增大,而断裂伸长率呈逐渐下降趋势,PA6的破坏方式由韧性断裂逐渐转变为脆性断裂.
對尼龍6 (PA6)進行不同缺口深度和不同缺口麯率半徑的單邊缺口拉伸試驗,同時採用SEM觀察斷口形貌.結果錶明,隨著缺口麯率半徑的增加,PA6缺口尖耑應力呈逐漸降低,而斷裂伸長率呈逐漸上升趨勢.缺口麯率半徑在0.1~0.5 mm範圍內時,拉伸斷裂功基本消耗在裂紋萌生階段,PA6裂紋擴展區錶現為脆性斷裂方式.噹缺口麯率半徑大于0.5 mm後,拉伸斷裂功主要消耗在裂紋擴展階段,PA6裂紋擴展區錶現為韌性斷裂方式.隨著缺口深度的增加,缺口附近應力集中程度增大,PA6塑性變形能力下降,缺口尖耑應力呈逐漸增大,而斷裂伸長率呈逐漸下降趨勢,PA6的破壞方式由韌性斷裂逐漸轉變為脆性斷裂.
대니룡6 (PA6)진행불동결구심도화불동결구곡솔반경적단변결구랍신시험,동시채용SEM관찰단구형모.결과표명,수착결구곡솔반경적증가,PA6결구첨단응력정축점강저,이단렬신장솔정축점상승추세.결구곡솔반경재0.1~0.5 mm범위내시,랍신단렬공기본소모재렬문맹생계단,PA6렬문확전구표현위취성단렬방식.당결구곡솔반경대우0.5 mm후,랍신단렬공주요소모재렬문확전계단,PA6렬문확전구표현위인성단렬방식.수착결구심도적증가,결구부근응력집중정도증대,PA6소성변형능력하강,결구첨단응력정축점증대,이단렬신장솔정축점하강추세,PA6적파배방식유인성단렬축점전변위취성단렬.