现代铸铁
現代鑄鐵
현대주철
MODERN CAST IRON
2014年
2期
89-92
,共4页
高Cr铸铁%亚临界处理%硬度
高Cr鑄鐵%亞臨界處理%硬度
고Cr주철%아림계처리%경도
high Cr cast iron%sub-critical treatment%hardness
介绍了高Cr铸铁的亚临界处理方法,并以w(Cr) 17%的高Cr铸铁大平面端衬板为对象,探讨了亚临界处理获得所需硬度的可能,以及亚临界处理对铸态组织要求和热处理工艺参数的作用规律.结果表明,在铸态基体组织主要为珠光体条件下,调整亚临界处理的温度和时间并不能有效提高铸件的硬度;最后通过将w(Mn)量提高到1.5%~1.8%,w(Si)量降低至0.4%~0.8%,使铸态基体以奥氏体为主,在550℃下保温6h的亚临界处理工艺下,使43~47 HRC的铸态硬度提高到52~54HRC,改善了产品的抗磨性能,且相对于淬火处理减少了能源消耗,也避免高温处理易引起变形的缺点.
介紹瞭高Cr鑄鐵的亞臨界處理方法,併以w(Cr) 17%的高Cr鑄鐵大平麵耑襯闆為對象,探討瞭亞臨界處理穫得所需硬度的可能,以及亞臨界處理對鑄態組織要求和熱處理工藝參數的作用規律.結果錶明,在鑄態基體組織主要為珠光體條件下,調整亞臨界處理的溫度和時間併不能有效提高鑄件的硬度;最後通過將w(Mn)量提高到1.5%~1.8%,w(Si)量降低至0.4%~0.8%,使鑄態基體以奧氏體為主,在550℃下保溫6h的亞臨界處理工藝下,使43~47 HRC的鑄態硬度提高到52~54HRC,改善瞭產品的抗磨性能,且相對于淬火處理減少瞭能源消耗,也避免高溫處理易引起變形的缺點.
개소료고Cr주철적아림계처리방법,병이w(Cr) 17%적고Cr주철대평면단츤판위대상,탐토료아림계처리획득소수경도적가능,이급아림계처리대주태조직요구화열처리공예삼수적작용규률.결과표명,재주태기체조직주요위주광체조건하,조정아림계처리적온도화시간병불능유효제고주건적경도;최후통과장w(Mn)량제고도1.5%~1.8%,w(Si)량강저지0.4%~0.8%,사주태기체이오씨체위주,재550℃하보온6h적아림계처리공예하,사43~47 HRC적주태경도제고도52~54HRC,개선료산품적항마성능,차상대우쉬화처리감소료능원소모,야피면고온처리역인기변형적결점.