林业机械与木工设备
林業機械與木工設備
임업궤계여목공설비
FORESTRY MACHINERY & WOODWORKING EQUIPMENT
2014年
6期
13-17
,共5页
热压干燥%单板%温度分布%双因子交互作用
熱壓榦燥%單闆%溫度分佈%雙因子交互作用
열압간조%단판%온도분포%쌍인자교호작용
hot-press drying%veneer%temperature distribution%two-factor interaction
选择压力(P)、热压板温度(T)、单板张数(N)三个因子各3个水平,进行完全随机试验,测定每张单板的温度变化,以靠近热压板处单板与中间单板的温差△T为指标,分析双因子交互作用对预干单板温度分布的影响。结果表明:在热压干燥初始、中间、最终三个阶段,各因子以及二因子、三因子之间的交互作用均对单板的温度分布有显著影响。①初始阶段,不同热压板温度下压力越大△T越小,不同压力下单板张数越少△T越小,不同热压板温度下单板张数越少△T越小。②中间阶段,对于不同压力,热压板温度为120℃下的△T最小;不同压力下,单板张数为5时的△T最小;不同单板张数下,120℃时的△T最小;③最终阶段,不同压力下热压板温度越低△T越小;不同压力下单板张数越少△T越小;对于不同单板张数,120℃时△T最小。
選擇壓力(P)、熱壓闆溫度(T)、單闆張數(N)三箇因子各3箇水平,進行完全隨機試驗,測定每張單闆的溫度變化,以靠近熱壓闆處單闆與中間單闆的溫差△T為指標,分析雙因子交互作用對預榦單闆溫度分佈的影響。結果錶明:在熱壓榦燥初始、中間、最終三箇階段,各因子以及二因子、三因子之間的交互作用均對單闆的溫度分佈有顯著影響。①初始階段,不同熱壓闆溫度下壓力越大△T越小,不同壓力下單闆張數越少△T越小,不同熱壓闆溫度下單闆張數越少△T越小。②中間階段,對于不同壓力,熱壓闆溫度為120℃下的△T最小;不同壓力下,單闆張數為5時的△T最小;不同單闆張數下,120℃時的△T最小;③最終階段,不同壓力下熱壓闆溫度越低△T越小;不同壓力下單闆張數越少△T越小;對于不同單闆張數,120℃時△T最小。
선택압력(P)、열압판온도(T)、단판장수(N)삼개인자각3개수평,진행완전수궤시험,측정매장단판적온도변화,이고근열압판처단판여중간단판적온차△T위지표,분석쌍인자교호작용대예간단판온도분포적영향。결과표명:재열압간조초시、중간、최종삼개계단,각인자이급이인자、삼인자지간적교호작용균대단판적온도분포유현저영향。①초시계단,불동열압판온도하압력월대△T월소,불동압력하단판장수월소△T월소,불동열압판온도하단판장수월소△T월소。②중간계단,대우불동압력,열압판온도위120℃하적△T최소;불동압력하,단판장수위5시적△T최소;불동단판장수하,120℃시적△T최소;③최종계단,불동압력하열압판온도월저△T월소;불동압력하단판장수월소△T월소;대우불동단판장수,120℃시△T최소。
In this study, 3 levels of pressure(P), platen temperature(T), and veneers number(N)are selected for completely random tests to test the temperature change of each veneer , with the taking temperature difference△T between the veneer next to the platen and veneer in the middle as an index, the effect of two-factor interaction on temperature distribution of pre-drying veneer is analyzed, with the result showing: at initial stage, middle stage, and end stage, the interaction between all factors; two factors and three factors has a significant effect of the temperature distribution of veneer.①At the initial stage, the greater the pressure at different platen temperature is , the smaller△T is.②At the middle stage, as for pressure,△T is the smallest when the platen temperature is 120℃; under different pressure,△T is the smallest when the number of veneers is 5; in the case of different numbers of veneers,△T is the smallest at 120℃.③at the final stage, under different pressure, the lower the platen temperature is, the smaller△T is; under different pressure, the smaller the number of veneers is, the smaller△T is; in the case of different numbers of veneers,△T is the smallest at 120℃.