中国有色金属学报(英文版)
中國有色金屬學報(英文版)
중국유색금속학보(영문판)
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA
2012年
z2期
445-449
,共5页
孙宏飞%李成杰%解洋%房文斌
孫宏飛%李成傑%解洋%房文斌
손굉비%리성걸%해양%방문빈
纯镁%大比率挤压%力学性能%晶粒细化%动态再结晶
純鎂%大比率擠壓%力學性能%晶粒細化%動態再結晶
순미%대비솔제압%역학성능%정립세화%동태재결정
pure magnesium%high ratio extrusion%mechanical properties%grain refinement%dynamic recrystallization
以纯镁铸锭作为坯料,经过两道次累计大比率挤压制备了棒材,并对最终的棒材进行退火处理.通过光学显微镜(OM)、力学性能测试和扫描电子显微镜(SEM)研究了挤压变形和退火处理对纯镁组织、性能以及断裂行为的影响.结果表明:在挤压变形过程中,由于动态再结晶的作用,材料的晶粒尺寸得到明显细化,从而显著地改善了材料的室温力学性能和断裂方式.经过一次挤压后,粗大的铸态晶粒细化到35 μm,屈服、抗拉强度和伸长率分别达到84 MPa、189 MPa和12%,所得棒材经再次挤压后,屈服强度超过120MPa,但是,由于加工硬化的作用,伸长率有所下降.对最终棒材进行退火处理后,平均晶粒尺寸为9~10 μm,屈服强度、抗拉强度分别达到124MPa、199MPa,伸长率为10.7%,材料的组织和性能得到明显改善.
以純鎂鑄錠作為坯料,經過兩道次纍計大比率擠壓製備瞭棒材,併對最終的棒材進行退火處理.通過光學顯微鏡(OM)、力學性能測試和掃描電子顯微鏡(SEM)研究瞭擠壓變形和退火處理對純鎂組織、性能以及斷裂行為的影響.結果錶明:在擠壓變形過程中,由于動態再結晶的作用,材料的晶粒呎吋得到明顯細化,從而顯著地改善瞭材料的室溫力學性能和斷裂方式.經過一次擠壓後,粗大的鑄態晶粒細化到35 μm,屈服、抗拉彊度和伸長率分彆達到84 MPa、189 MPa和12%,所得棒材經再次擠壓後,屈服彊度超過120MPa,但是,由于加工硬化的作用,伸長率有所下降.對最終棒材進行退火處理後,平均晶粒呎吋為9~10 μm,屈服彊度、抗拉彊度分彆達到124MPa、199MPa,伸長率為10.7%,材料的組織和性能得到明顯改善.
이순미주정작위배료,경과량도차루계대비솔제압제비료봉재,병대최종적봉재진행퇴화처리.통과광학현미경(OM)、역학성능측시화소묘전자현미경(SEM)연구료제압변형화퇴화처리대순미조직、성능이급단렬행위적영향.결과표명:재제압변형과정중,유우동태재결정적작용,재료적정립척촌득도명현세화,종이현저지개선료재료적실온역학성능화단렬방식.경과일차제압후,조대적주태정립세화도35 μm,굴복、항랍강도화신장솔분별체도84 MPa、189 MPa화12%,소득봉재경재차제압후,굴복강도초과120MPa,단시,유우가공경화적작용,신장솔유소하강.대최종봉재진행퇴화처리후,평균정립척촌위9~10 μm,굴복강도、항랍강도분별체도124MPa、199MPa,신장솔위10.7%,재료적조직화성능득도명현개선.