稀有金属材料与工程
稀有金屬材料與工程
희유금속재료여공정
RARE METAL MATERIALS AND ENGINEERNG
2013年
12期
2598-2601
,共4页
张俊杰%张丽霞%亓钧雷%张大磊%冯吉才
張俊傑%張麗霞%亓鈞雷%張大磊%馮吉纔
장준걸%장려하%기균뢰%장대뢰%풍길재
SiO2复合材料%TC4%钎焊%界面组织%抗剪强度
SiO2複閤材料%TC4%釬銲%界麵組織%抗剪彊度
SiO2복합재료%TC4%천한%계면조직%항전강도
SiO2 composite%TC4%brazing%interfacial microstructure%shear strength
采用AgCu-4.5Ti钎料直接钎焊TC4钛合金与SiO2复合材料,研究了接头界面组织结构及形成机理,分析了不同工艺参数下界面变化对接头抗剪强度的影响.研究表明:接头界面典型结构为SiO2复合材料/TiSi2/Cu4Ti3+Cu3Ti3O/Ag(s,s)+Cu(s,s)/TiCu/Ti2Cu/α,β-Ti/TC4;钎焊温度的升高可促进两侧母材界面反应层厚度的增加,同时钎缝中部的AgCu共晶组织消失,化合物相增多;随着接头界面结构的变化,接头抗剪强度表现出先升高后降低的趋势:当钎焊温度为850℃,保温10 min时,接头室温最高抗剪强度达到7.8 MPa.
採用AgCu-4.5Ti釬料直接釬銲TC4鈦閤金與SiO2複閤材料,研究瞭接頭界麵組織結構及形成機理,分析瞭不同工藝參數下界麵變化對接頭抗剪彊度的影響.研究錶明:接頭界麵典型結構為SiO2複閤材料/TiSi2/Cu4Ti3+Cu3Ti3O/Ag(s,s)+Cu(s,s)/TiCu/Ti2Cu/α,β-Ti/TC4;釬銲溫度的升高可促進兩側母材界麵反應層厚度的增加,同時釬縫中部的AgCu共晶組織消失,化閤物相增多;隨著接頭界麵結構的變化,接頭抗剪彊度錶現齣先升高後降低的趨勢:噹釬銲溫度為850℃,保溫10 min時,接頭室溫最高抗剪彊度達到7.8 MPa.
채용AgCu-4.5Ti천료직접천한TC4태합금여SiO2복합재료,연구료접두계면조직결구급형성궤리,분석료불동공예삼수하계면변화대접두항전강도적영향.연구표명:접두계면전형결구위SiO2복합재료/TiSi2/Cu4Ti3+Cu3Ti3O/Ag(s,s)+Cu(s,s)/TiCu/Ti2Cu/α,β-Ti/TC4;천한온도적승고가촉진량측모재계면반응층후도적증가,동시천봉중부적AgCu공정조직소실,화합물상증다;수착접두계면결구적변화,접두항전강도표현출선승고후강저적추세:당천한온도위850℃,보온10 min시,접두실온최고항전강도체도7.8 MPa.