涂料工业
塗料工業
도료공업
PAINT & COATINGS INDUSTRY
2014年
1期
18-23
,共6页
沈琴%穆颖%朱艳虹%常春%杨建红
瀋琴%穆穎%硃豔虹%常春%楊建紅
침금%목영%주염홍%상춘%양건홍
桐油酸%丙烯酸酯%乳液%性能
桐油痠%丙烯痠酯%乳液%性能
동유산%병희산지%유액%성능
tung oil acid%acrylate%emulsion%performance
以丙烯酸丁酯(BA)、甲基丙烯酸甲酯(MMA)、桐油酸、过硫酸钾(KPS)、十二烷基硫酸钠(SDS)、壬基酚聚氧乙烯醚(NP-10)为原料合成了丙烯酸酯乳液,研究了桐油酸含量、单体配比、乳化剂含量对乳液及其涂膜性能的影响,并采用FT-IR、SEM、粒径及Zeta电位分析仪和涂膜性能测试仪对乳液及涂膜的结构和性能进行了测试.研究结果表明:桐油酸的加入使得乳胶粒的形态由球形变为方体或柱体,涂膜的吸水率有所减小,疏水性、硬度、附着力有所提高.当桐油酸含量为1%,乳化剂含量为3%,m(BA)∶m(MMA)=1∶1时,乳液转化率达到98.4%,凝胶率为0.012%,涂膜的硬度、附着力从不加桐油酸时的B和7级提升到5H和2级.
以丙烯痠丁酯(BA)、甲基丙烯痠甲酯(MMA)、桐油痠、過硫痠鉀(KPS)、十二烷基硫痠鈉(SDS)、壬基酚聚氧乙烯醚(NP-10)為原料閤成瞭丙烯痠酯乳液,研究瞭桐油痠含量、單體配比、乳化劑含量對乳液及其塗膜性能的影響,併採用FT-IR、SEM、粒徑及Zeta電位分析儀和塗膜性能測試儀對乳液及塗膜的結構和性能進行瞭測試.研究結果錶明:桐油痠的加入使得乳膠粒的形態由毬形變為方體或柱體,塗膜的吸水率有所減小,疏水性、硬度、附著力有所提高.噹桐油痠含量為1%,乳化劑含量為3%,m(BA)∶m(MMA)=1∶1時,乳液轉化率達到98.4%,凝膠率為0.012%,塗膜的硬度、附著力從不加桐油痠時的B和7級提升到5H和2級.
이병희산정지(BA)、갑기병희산갑지(MMA)、동유산、과류산갑(KPS)、십이완기류산납(SDS)、임기분취양을희미(NP-10)위원료합성료병희산지유액,연구료동유산함량、단체배비、유화제함량대유액급기도막성능적영향,병채용FT-IR、SEM、립경급Zeta전위분석의화도막성능측시의대유액급도막적결구화성능진행료측시.연구결과표명:동유산적가입사득유효립적형태유구형변위방체혹주체,도막적흡수솔유소감소,소수성、경도、부착력유소제고.당동유산함량위1%,유화제함량위3%,m(BA)∶m(MMA)=1∶1시,유액전화솔체도98.4%,응효솔위0.012%,도막적경도、부착력종불가동유산시적B화7급제승도5H화2급.