粉末冶金技术
粉末冶金技術
분말야금기술
POWDER METALLURGY TECHNOLOGY
2013年
2期
114-118
,共5页
粉末冶金%温压%410L%烧结
粉末冶金%溫壓%410L%燒結
분말야금%온압%410L%소결
为了研究温压工艺对410L不锈钢粉末的适用性,测定了410L粉末温压成形后的生坯密度和生坯强度,并进一步研究了温压压坯的烧结性能.结果表明,温压工艺能显著提高410L不锈钢粉末压坯的生坯密度和生坯强度,在110℃和700MPa压力下,温压410L不锈钢粉末的生坯密度和生坯强度为6.72g/cm3和29.6MPa,分别比冷压压坯提高了0.12g/cm3和5.5MPa.真空烧结60min后,410L不锈钢粉末压坯的烧结密度和硬度随着烧结温度的上升而提高,抗拉强度则随着烧结温度的上升而降低.在1 230℃烧结60min,其烧结密度为7.45g/cm3,硬度为65HRB,抗拉强度为410MPa,伸长率为29.5%.
為瞭研究溫壓工藝對410L不鏽鋼粉末的適用性,測定瞭410L粉末溫壓成形後的生坯密度和生坯彊度,併進一步研究瞭溫壓壓坯的燒結性能.結果錶明,溫壓工藝能顯著提高410L不鏽鋼粉末壓坯的生坯密度和生坯彊度,在110℃和700MPa壓力下,溫壓410L不鏽鋼粉末的生坯密度和生坯彊度為6.72g/cm3和29.6MPa,分彆比冷壓壓坯提高瞭0.12g/cm3和5.5MPa.真空燒結60min後,410L不鏽鋼粉末壓坯的燒結密度和硬度隨著燒結溫度的上升而提高,抗拉彊度則隨著燒結溫度的上升而降低.在1 230℃燒結60min,其燒結密度為7.45g/cm3,硬度為65HRB,抗拉彊度為410MPa,伸長率為29.5%.
위료연구온압공예대410L불수강분말적괄용성,측정료410L분말온압성형후적생배밀도화생배강도,병진일보연구료온압압배적소결성능.결과표명,온압공예능현저제고410L불수강분말압배적생배밀도화생배강도,재110℃화700MPa압력하,온압410L불수강분말적생배밀도화생배강도위6.72g/cm3화29.6MPa,분별비냉압압배제고료0.12g/cm3화5.5MPa.진공소결60min후,410L불수강분말압배적소결밀도화경도수착소결온도적상승이제고,항랍강도칙수착소결온도적상승이강저.재1 230℃소결60min,기소결밀도위7.45g/cm3,경도위65HRB,항랍강도위410MPa,신장솔위29.5%.