浙江林业科技
浙江林業科技
절강임업과기
JOURNAL OF ZHEJIANG FORESTRY SCIENCE AND TECHNOLOGY
2012年
6期
14-17
,共4页
于利%姚迟强%余肖红%李延军%刘红征
于利%姚遲彊%餘肖紅%李延軍%劉紅徵
우리%요지강%여초홍%리연군%류홍정
密实%单板层积材%热压工艺%力学性能
密實%單闆層積材%熱壓工藝%力學性能
밀실%단판층적재%열압공예%역학성능
以自制低分子量酚醛树脂为胶黏剂,采用热压工艺对杉木单板进行密实化试验,研究干燥温度、压缩率、热压温度和热压时间对密实型杉木单板层积材力学性能的影响.结果表明:压缩率对层积材力学性能影响最大,其次是干燥温度、热压温度和热压时间;随着压缩率和热压温度的提高,板材的MOE、MOR都有不同程度的提高;随着干燥温度的提升和热压时间的延长,板材的MOE、MOR都呈先增大后减小的趋势;综合考虑,确定密实型杉木单板层积材的最佳热压工艺为:干燥温度60℃、压缩率35%、热压温度145℃、热压时间1.0 min/mm,在此热压工艺条件下制得的板材,其MOE和MOR分别达到了GB/T 20241-2006《单板层积材》120E级和180E优级.
以自製低分子量酚醛樹脂為膠黏劑,採用熱壓工藝對杉木單闆進行密實化試驗,研究榦燥溫度、壓縮率、熱壓溫度和熱壓時間對密實型杉木單闆層積材力學性能的影響.結果錶明:壓縮率對層積材力學性能影響最大,其次是榦燥溫度、熱壓溫度和熱壓時間;隨著壓縮率和熱壓溫度的提高,闆材的MOE、MOR都有不同程度的提高;隨著榦燥溫度的提升和熱壓時間的延長,闆材的MOE、MOR都呈先增大後減小的趨勢;綜閤攷慮,確定密實型杉木單闆層積材的最佳熱壓工藝為:榦燥溫度60℃、壓縮率35%、熱壓溫度145℃、熱壓時間1.0 min/mm,在此熱壓工藝條件下製得的闆材,其MOE和MOR分彆達到瞭GB/T 20241-2006《單闆層積材》120E級和180E優級.
이자제저분자량분철수지위효점제,채용열압공예대삼목단판진행밀실화시험,연구간조온도、압축솔、열압온도화열압시간대밀실형삼목단판층적재역학성능적영향.결과표명:압축솔대층적재역학성능영향최대,기차시간조온도、열압온도화열압시간;수착압축솔화열압온도적제고,판재적MOE、MOR도유불동정도적제고;수착간조온도적제승화열압시간적연장,판재적MOE、MOR도정선증대후감소적추세;종합고필,학정밀실형삼목단판층적재적최가열압공예위:간조온도60℃、압축솔35%、열압온도145℃、열압시간1.0 min/mm,재차열압공예조건하제득적판재,기MOE화MOR분별체도료GB/T 20241-2006《단판층적재》120E급화180E우급.