强激光与粒子束
彊激光與粒子束
강격광여입자속
HIGH POWER LASER AND PARTICLEBEAMS
2013年
7期
1715-1718
,共4页
高重频%激光能量%虚拟唇口%来流捕获率%流动控制
高重頻%激光能量%虛擬脣口%來流捕穫率%流動控製
고중빈%격광능량%허의진구%래류포획솔%류동공제
针对来流马赫数低于设计值时,吸气式冲压发动机进气道进气捕获率降低的问题,在唇口上游沉积高重频激光能量使气流偏折以提高进气捕获率.在马赫数为5.0、静压和静温分别为2 551.6 Pa和116.7K的条件下,通过求解二维非定常可压缩RANS方程,数值研究了高重频激光能量注入提高进气捕获率的作用机制,通过在预想最优能量沉积点附近寻优的方法确定了最佳的能量注入点,结果表明:在该位置沉积频率100 kHz、平均功率500 W的激光能量形成的虚拟唇口可以使来流捕获率由63%提高至97%.结果证明了高重频激光能量注入提高进气捕获率的潜在应用价值,并为能量注入位置的优化选择提供了方法.
針對來流馬赫數低于設計值時,吸氣式遲壓髮動機進氣道進氣捕穫率降低的問題,在脣口上遊沉積高重頻激光能量使氣流偏摺以提高進氣捕穫率.在馬赫數為5.0、靜壓和靜溫分彆為2 551.6 Pa和116.7K的條件下,通過求解二維非定常可壓縮RANS方程,數值研究瞭高重頻激光能量註入提高進氣捕穫率的作用機製,通過在預想最優能量沉積點附近尋優的方法確定瞭最佳的能量註入點,結果錶明:在該位置沉積頻率100 kHz、平均功率500 W的激光能量形成的虛擬脣口可以使來流捕穫率由63%提高至97%.結果證明瞭高重頻激光能量註入提高進氣捕穫率的潛在應用價值,併為能量註入位置的優化選擇提供瞭方法.
침대래류마혁수저우설계치시,흡기식충압발동궤진기도진기포획솔강저적문제,재진구상유침적고중빈격광능량사기류편절이제고진기포획솔.재마혁수위5.0、정압화정온분별위2 551.6 Pa화116.7K적조건하,통과구해이유비정상가압축RANS방정,수치연구료고중빈격광능량주입제고진기포획솔적작용궤제,통과재예상최우능량침적점부근심우적방법학정료최가적능량주입점,결과표명:재해위치침적빈솔100 kHz、평균공솔500 W적격광능량형성적허의진구가이사래류포획솔유63%제고지97%.결과증명료고중빈격광능량주입제고진기포획솔적잠재응용개치,병위능량주입위치적우화선택제공료방법.