兵器材料科学与工程
兵器材料科學與工程
병기재료과학여공정
Ordnance Material Science and Engineering
2013年
3期
89-91
,共3页
时雨%卫广智%赵飞
時雨%衛廣智%趙飛
시우%위엄지%조비
18Ni马氏体时效钢%时效%力学特性%Ni3Mo%Ni3Ti
18Ni馬氏體時效鋼%時效%力學特性%Ni3Mo%Ni3Ti
18Ni마씨체시효강%시효%역학특성%Ni3Mo%Ni3Ti
18Ni maraging steel%aging%mechanical properties%Ni3Mo%Ni3Ti
研究不同时效温度和时间对820℃×1 h固溶处理后的18Ni马氏体时效钢硬度的影响规律。研究了480℃时效3 h 和4 h 的拉伸性能,并利用金相显微镜、扫描电镜对时效后的组织和断口进行观察分析。结果表明:当时效温度较低(460℃),时效3 h达到峰值的98%左右;在较高温度(520℃)时效,10 min左右即可达到该水平;最优时效工艺为480℃×3 h;两种时效工艺下的断口有明显的延伸和缩颈,中心存在大量韧窝,为典型的韧性断裂。
研究不同時效溫度和時間對820℃×1 h固溶處理後的18Ni馬氏體時效鋼硬度的影響規律。研究瞭480℃時效3 h 和4 h 的拉伸性能,併利用金相顯微鏡、掃描電鏡對時效後的組織和斷口進行觀察分析。結果錶明:噹時效溫度較低(460℃),時效3 h達到峰值的98%左右;在較高溫度(520℃)時效,10 min左右即可達到該水平;最優時效工藝為480℃×3 h;兩種時效工藝下的斷口有明顯的延伸和縮頸,中心存在大量韌窩,為典型的韌性斷裂。
연구불동시효온도화시간대820℃×1 h고용처리후적18Ni마씨체시효강경도적영향규률。연구료480℃시효3 h 화4 h 적랍신성능,병이용금상현미경、소묘전경대시효후적조직화단구진행관찰분석。결과표명:당시효온도교저(460℃),시효3 h체도봉치적98%좌우;재교고온도(520℃)시효,10 min좌우즉가체도해수평;최우시효공예위480℃×3 h;량충시효공예하적단구유명현적연신화축경,중심존재대량인와,위전형적인성단렬。
The effects of different aging temperature and time on hardness of 18Ni maraging steel which was solution?treated at 820 ℃ for 1 h were studied. The results show that when aging at 460 ℃ for 3 h tensile strenght reaches about 98% of peak value, while aging at 520 ℃ for about 10 min,tensile strenght rcaches the same level. Aging at 480 ℃ for 3 h is the optimal aging process in this experiments. The fracture is obvious extension and necking and a large number of dimples occur in the center. It is typical ductile fracture under two kinds of aging process.