激光杂志
激光雜誌
격광잡지
LASER JOURNAL
2014年
5期
14-15,19
,共3页
液晶染料%局域模%电场调控%光激发
液晶染料%跼域模%電場調控%光激髮
액정염료%국역모%전장조공%광격발
Dye doped liquid%Defect mode%Electric control%Lasing
基于液晶的电场调控特性及激光染料作为增益介质的增益模型,通过传输矩阵法理论研究了液晶染料填充一维光子晶体局域模的电场调控及其光激发特性。数值结果表明:随着垂直入射光和电场方向的夹角θ的增大,局域模波长向短波方向移动;当角度θ在(0°,90°)范围内变化时,局域模波长最大调控量达56.7nm;激光染料泵浦后不改变局域模的位置,但局域模的透射率变大了;随着增益系数的增大,局域模透射率先增大后减小,不同局域模对应不同的泵浦阈值,并且随着夹角θ的增大局域模对应的泵浦阈值将减小。
基于液晶的電場調控特性及激光染料作為增益介質的增益模型,通過傳輸矩陣法理論研究瞭液晶染料填充一維光子晶體跼域模的電場調控及其光激髮特性。數值結果錶明:隨著垂直入射光和電場方嚮的夾角θ的增大,跼域模波長嚮短波方嚮移動;噹角度θ在(0°,90°)範圍內變化時,跼域模波長最大調控量達56.7nm;激光染料泵浦後不改變跼域模的位置,但跼域模的透射率變大瞭;隨著增益繫數的增大,跼域模透射率先增大後減小,不同跼域模對應不同的泵浦閾值,併且隨著夾角θ的增大跼域模對應的泵浦閾值將減小。
기우액정적전장조공특성급격광염료작위증익개질적증익모형,통과전수구진법이론연구료액정염료전충일유광자정체국역모적전장조공급기광격발특성。수치결과표명:수착수직입사광화전장방향적협각θ적증대,국역모파장향단파방향이동;당각도θ재(0°,90°)범위내변화시,국역모파장최대조공량체56.7nm;격광염료빙포후불개변국역모적위치,단국역모적투사솔변대료;수착증익계수적증대,국역모투사솔선증대후감소,불동국역모대응불동적빙포역치,병차수착협각θ적증대국역모대응적빙포역치장감소。
Based on the control characteristics of liquid crystal and the gain model of laser dye, the control char-acteristics of one-dimensional dye doped liquid crystal photonic crystal defect mode with single defect layer and its Lasing were studied using the transfer matrix method. The numerical results showed that the wavelength of defect modes move to short-wave as the increasing of angleθbetween the direction of the incident light and external elec-tric field. The maximum regulation of defect mode wavelength could reach 56.7nm when angleθranges from 0 de-gree to 90 degree. After laser dye pumped, the position of defect modes will not change, but its transmissivity in-creases. The transmissivity of defect modes firstly increases and then decreases as the increasing of the gain coeffi-cient and different defect modes correspond to different pumping thresholds. And the pumping thresholds will de-crease as the increasing of angleθ.