科学技术与工程
科學技術與工程
과학기술여공정
SCIENCE TECHNOLOGY AND ENGINEERING
2014年
1期
29-35
,共7页
陈春燕%李勇%曾志新%陈创新
陳春燕%李勇%曾誌新%陳創新
진춘연%리용%증지신%진창신
热管%烧结%沟槽%热阻
熱管%燒結%溝槽%熱阻
열관%소결%구조%열조
heat pipe%sintered%groove%thermal resistance
通过采用直径分别为5.5mm及6 mm的芯棒制作外径是8 mm、烧结层长度分别占总长度的1/3、2/3及1的复合型吸液芯热管(分别命名为GO、GT和GF),对其极限传递功率(MHTP)、蒸发端、冷凝端及总热阻进行比较.研究烧结长度对复合型吸液芯热管传热性能的影响.工质的填充状态有两种:①吸液芯孔隙填满工质;②填充相同工质量.结果发现:两种工质灌注状态对热阻的影响较小,对MHTP的影响较大.芯棒直径5.5 mm时,状态①中,GO、GT、GF的MHTP都达100W以上;状态②中,GF则只达到80 W.芯棒直径6 mm时,状态①中,GO、GT、GF的MHTP分别为100 W以上、80 W、60W;状态②中,GO、GT、GF的MHTP则分别为80 W、100 W以上、80 W.减少吸液芯烧结层的长度可有效降低热管总热阻,吸液芯厚度相同时,GT或GO总热阻相对GF至少可减少33%.输入功率60~100 W时,同根热管总热阻大小变化<0.01℃/W.吸液芯厚度增加0.25 mm时,相同烧结长度的热管总热阻大小相差<0.01℃/W.两种工质灌注状态都表明烧结层长度对复合热管蒸发段热阻影响较小,主要对冷凝端及总热阻有影响,其中热管冷凝端热阻的变化趋势与总热阻相同.
通過採用直徑分彆為5.5mm及6 mm的芯棒製作外徑是8 mm、燒結層長度分彆佔總長度的1/3、2/3及1的複閤型吸液芯熱管(分彆命名為GO、GT和GF),對其極限傳遞功率(MHTP)、蒸髮耑、冷凝耑及總熱阻進行比較.研究燒結長度對複閤型吸液芯熱管傳熱性能的影響.工質的填充狀態有兩種:①吸液芯孔隙填滿工質;②填充相同工質量.結果髮現:兩種工質灌註狀態對熱阻的影響較小,對MHTP的影響較大.芯棒直徑5.5 mm時,狀態①中,GO、GT、GF的MHTP都達100W以上;狀態②中,GF則隻達到80 W.芯棒直徑6 mm時,狀態①中,GO、GT、GF的MHTP分彆為100 W以上、80 W、60W;狀態②中,GO、GT、GF的MHTP則分彆為80 W、100 W以上、80 W.減少吸液芯燒結層的長度可有效降低熱管總熱阻,吸液芯厚度相同時,GT或GO總熱阻相對GF至少可減少33%.輸入功率60~100 W時,同根熱管總熱阻大小變化<0.01℃/W.吸液芯厚度增加0.25 mm時,相同燒結長度的熱管總熱阻大小相差<0.01℃/W.兩種工質灌註狀態都錶明燒結層長度對複閤熱管蒸髮段熱阻影響較小,主要對冷凝耑及總熱阻有影響,其中熱管冷凝耑熱阻的變化趨勢與總熱阻相同.
통과채용직경분별위5.5mm급6 mm적심봉제작외경시8 mm、소결층장도분별점총장도적1/3、2/3급1적복합형흡액심열관(분별명명위GO、GT화GF),대기겁한전체공솔(MHTP)、증발단、냉응단급총열조진행비교.연구소결장도대복합형흡액심열관전열성능적영향.공질적전충상태유량충:①흡액심공극전만공질;②전충상동공질량.결과발현:량충공질관주상태대열조적영향교소,대MHTP적영향교대.심봉직경5.5 mm시,상태①중,GO、GT、GF적MHTP도체100W이상;상태②중,GF칙지체도80 W.심봉직경6 mm시,상태①중,GO、GT、GF적MHTP분별위100 W이상、80 W、60W;상태②중,GO、GT、GF적MHTP칙분별위80 W、100 W이상、80 W.감소흡액심소결층적장도가유효강저열관총열조,흡액심후도상동시,GT혹GO총열조상대GF지소가감소33%.수입공솔60~100 W시,동근열관총열조대소변화<0.01℃/W.흡액심후도증가0.25 mm시,상동소결장도적열관총열조대소상차<0.01℃/W.량충공질관주상태도표명소결층장도대복합열관증발단열조영향교소,주요대냉응단급총열조유영향,기중열관냉응단열조적변화추세여총열조상동.