绝缘材料
絕緣材料
절연재료
INSULATING MATERIALS
2014年
3期
94-98,102
,共6页
邹林%涂扬%孟永鹏%成永红%张科%李锐海%刘通
鄒林%塗颺%孟永鵬%成永紅%張科%李銳海%劉通
추림%도양%맹영붕%성영홍%장과%리예해%류통
界面%硅橡胶%电极系统%局部放电
界麵%硅橡膠%電極繫統%跼部放電
계면%규상효%전겁계통%국부방전
interface%silicone rubber%electrode system%partial discharge
设计了聚乙烯与硅橡胶界面在不同界面压力下的局部放电试验系统,通过施加一定的界面压强模拟电缆附件中的界面压强,研究不同界面压强和不同表面粗糙度的聚乙烯对聚乙烯与硅橡胶界面的局部放电起始电压和局部放电特性的影响,通过建立界面接触放电模型和界面电场分布计算方法计算了局部放电起始电压,并结合试验结果分析界面放电机理。结果表明:聚乙烯表面越粗糙,局部放电起始电压越低;随着界面压强的增大,界面的局部放电起始电压增大,局部放电量逐渐减小,总放电次数也减小。
設計瞭聚乙烯與硅橡膠界麵在不同界麵壓力下的跼部放電試驗繫統,通過施加一定的界麵壓彊模擬電纜附件中的界麵壓彊,研究不同界麵壓彊和不同錶麵粗糙度的聚乙烯對聚乙烯與硅橡膠界麵的跼部放電起始電壓和跼部放電特性的影響,通過建立界麵接觸放電模型和界麵電場分佈計算方法計算瞭跼部放電起始電壓,併結閤試驗結果分析界麵放電機理。結果錶明:聚乙烯錶麵越粗糙,跼部放電起始電壓越低;隨著界麵壓彊的增大,界麵的跼部放電起始電壓增大,跼部放電量逐漸減小,總放電次數也減小。
설계료취을희여규상효계면재불동계면압력하적국부방전시험계통,통과시가일정적계면압강모의전람부건중적계면압강,연구불동계면압강화불동표면조조도적취을희대취을희여규상효계면적국부방전기시전압화국부방전특성적영향,통과건립계면접촉방전모형화계면전장분포계산방법계산료국부방전기시전압,병결합시험결과분석계면방전궤리。결과표명:취을희표면월조조,국부방전기시전압월저;수착계면압강적증대,계면적국부방전기시전압증대,국부방전량축점감소,총방전차수야감소。
A partial discharge experimental system under different interface pressures between polyethylene and silicone rubber is established. By applying certain pressure to simulate the interface pressure of cable accessory, the effects of interface pressure and surface roughness of polyethylene on the partial discharge initial voltage and partial discharge characteristics between polyethylene and silicone rubber were studied. The partial discharge initial voltage was calculated by the interface breakdown model and calculation method of electric field distribution, and the interface partial discharge mechanism was analyzed. The re-sults show that the more roughness of the polyethylene surface, the lower the partial discharge initial volt-age is. With the increase of the interface pressure, the partial discharge initial voltage increases, the mag-nitude of partial discharge decreases, and the total discharge times decreases also.