流体机械
流體機械
류체궤계
FLUID MACHINERY
2014年
6期
21-25
,共5页
何永明%穆塔里夫·阿赫迈德%刘毅龙
何永明%穆塔裏伕·阿赫邁德%劉毅龍
하영명%목탑리부·아혁매덕%류의룡
机械密封%摩擦副%热-结构耦合%温度-力载荷%计算流体力学
機械密封%摩抆副%熱-結構耦閤%溫度-力載荷%計算流體力學
궤계밀봉%마찰부%열-결구우합%온도-력재하%계산류체역학
mechanicalseal%frictionpair%thermal-structurecoupling%temperature-forceload%CFD
以热-结构耦合数值计算理论为基础,同时施加温度和力载荷边界条件,对处于高速、高压等高参数极端工况热油泵用波纹管机械密封装置摩擦副界面进行了热-结构耦合数值建模与计算分析。研究了密封环摩擦副界面的温度场特点及温度、热应力分布规律,分析了密封环在温度载荷和力载荷耦合作用下密封环的变形情况。结果表明:最高温度产生在摩擦副内径处,最大热变形在摩擦副外径处;动静环配对材料的导热系数越大,产生的最高温度就越小;在摩擦副的外径侧产生的变形有利于形成收敛型间隙。
以熱-結構耦閤數值計算理論為基礎,同時施加溫度和力載荷邊界條件,對處于高速、高壓等高參數極耑工況熱油泵用波紋管機械密封裝置摩抆副界麵進行瞭熱-結構耦閤數值建模與計算分析。研究瞭密封環摩抆副界麵的溫度場特點及溫度、熱應力分佈規律,分析瞭密封環在溫度載荷和力載荷耦閤作用下密封環的變形情況。結果錶明:最高溫度產生在摩抆副內徑處,最大熱變形在摩抆副外徑處;動靜環配對材料的導熱繫數越大,產生的最高溫度就越小;在摩抆副的外徑側產生的變形有利于形成收斂型間隙。
이열-결구우합수치계산이론위기출,동시시가온도화력재하변계조건,대처우고속、고압등고삼수겁단공황열유빙용파문관궤계밀봉장치마찰부계면진행료열-결구우합수치건모여계산분석。연구료밀봉배마찰부계면적온도장특점급온도、열응력분포규률,분석료밀봉배재온도재하화력재하우합작용하밀봉배적변형정황。결과표명:최고온도산생재마찰부내경처,최대열변형재마찰부외경처;동정배배대재료적도열계수월대,산생적최고온도취월소;재마찰부적외경측산생적변형유리우형성수렴형간극。
Thisresearchbasedonthethermal-structurecouplingnumericalcomputationaltheoryandsimultaneouslyapplying the temperature-force load to the boundary conditions,the numerical modeling and analysis of the thermal-structure coupling is put to the friction pair interface of sealing ring for the heat pump bellow mechanical seal in high-speed and high-pressure and such on high parameter complex working conditions.The temperature field characteristics,temperature and thermal-stress distribution law of friction pair interface of seal ring were studied;meanwhile,the deformation of the sealing ring under the coupling effect of temperature-force load were analyzed.Results show that the maximum temperature produced at the inner diameter of the friction pair and the maximum thermal deformation at the outer diameter;The greater thermal conductivity pairing material of seal ring, the smaller maximum temperature were produced;The deformation at the outer diameter of the friction pair conducive to conver-gent space.