桉树科技
桉樹科技
안수과기
EUCALYPT SCIENCE & TECHNOLOGY
2014年
2期
46-49
,共4页
温晓霞%薛忠%陈少雄%李慧
溫曉霞%薛忠%陳少雄%李慧
온효하%설충%진소웅%리혜
苗木移栽器%疲劳%Workbench
苗木移栽器%疲勞%Workbench
묘목이재기%피로%Workbench
seedling planting device%fatigue analysis%Workbench
手持式桉树幼苗种植器是一种简易的苗木种植辅助工具,在林地面积较小、林地为山地时,由于常常不适宜使用大型机械化作业,此时有广泛实用价值。本研究针对自行设计的手持式桉树幼苗种植器动杆部分使用SolidWorks软件进行三维实体建模并导入Ansys-Workbench软件开展有限元静力学分析,在此基础上进行疲劳分析,找出其薄弱区域和寿命曲线,通过分析得出最大破坏应力为3.6772×108Pa,最小安全因子仅为0.26047,100%载荷条件下循环寿命约为5000次,各指标的限制因素均出现在焊接部位。
手持式桉樹幼苗種植器是一種簡易的苗木種植輔助工具,在林地麵積較小、林地為山地時,由于常常不適宜使用大型機械化作業,此時有廣汎實用價值。本研究針對自行設計的手持式桉樹幼苗種植器動桿部分使用SolidWorks軟件進行三維實體建模併導入Ansys-Workbench軟件開展有限元靜力學分析,在此基礎上進行疲勞分析,找齣其薄弱區域和壽命麯線,通過分析得齣最大破壞應力為3.6772×108Pa,最小安全因子僅為0.26047,100%載荷條件下循環壽命約為5000次,各指標的限製因素均齣現在銲接部位。
수지식안수유묘충식기시일충간역적묘목충식보조공구,재임지면적교소、임지위산지시,유우상상불괄의사용대형궤계화작업,차시유엄범실용개치。본연구침대자행설계적수지식안수유묘충식기동간부분사용SolidWorks연건진행삼유실체건모병도입Ansys-Workbench연건개전유한원정역학분석,재차기출상진행피로분석,조출기박약구역화수명곡선,통과분석득출최대파배응력위3.6772×108Pa,최소안전인자부위0.26047,100%재하조건하순배수명약위5000차,각지표적한제인소균출현재한접부위。
The hand-held seedling planting device is a simple auxiliary tool which can be used in seedling transplantation;it will be widely used during to the unavailable mechanical operation under the small forest area and mountainous region. In this study, the rod part of the hand-held seedling planting device would be modeled through the SoldiWorks software and the Finite static analysis could be conducted with introducing the Ansys-Workbench software. Based on these works, the fatigue analysis can be conducted, the weak areas can be found and the life curve can be drew. According to the analysis, the maximum fail stress is 3.677 2 × 108Pa,the minimum safety factor is 0.260 47,the cycle life was about 5 000 times under full load. The limit factor is the welding position.