沈阳化工大学学报
瀋暘化工大學學報
침양화공대학학보
JOURNAL OF SHENYANG INSTITUTE OF CHEMICAL TECHNOLOGY
2014年
3期
202-205
,共4页
脉冲电沉积%工艺参数%镀层性能
脈遲電沉積%工藝參數%鍍層性能
맥충전침적%공예삼수%도층성능
采用脉冲电镀方法在紫铜片表面制备均匀光亮光滑的镍镀层.借助扫描电子显微镜(SEM)进行分析,并对其镀层结合力、孔隙率、耐磨性等测试考察镀层性能和结构.为获取最适宜的工艺参数,研究脉冲温度、平均电流密度、占空比对镍镀层显微硬度的影响.通过磨损失重测试,脉冲电镀镍镀层的耐磨性能远远高于直流镍镀层.最佳工艺条件为:硫酸镍300 g/L、氯化镍50 g/L、硼酸40 g/L、平均电流密度为3 A/dm2、占空比为50%、镀液温度为40~60℃.结果表明:在适宜的脉冲条件下,镀层结构能够得到进一步的细化,从而获得致密、平整、均匀、光亮的镀层,且镀层与铜基体结合良好.
採用脈遲電鍍方法在紫銅片錶麵製備均勻光亮光滑的鎳鍍層.藉助掃描電子顯微鏡(SEM)進行分析,併對其鍍層結閤力、孔隙率、耐磨性等測試攷察鍍層性能和結構.為穫取最適宜的工藝參數,研究脈遲溫度、平均電流密度、佔空比對鎳鍍層顯微硬度的影響.通過磨損失重測試,脈遲電鍍鎳鍍層的耐磨性能遠遠高于直流鎳鍍層.最佳工藝條件為:硫痠鎳300 g/L、氯化鎳50 g/L、硼痠40 g/L、平均電流密度為3 A/dm2、佔空比為50%、鍍液溫度為40~60℃.結果錶明:在適宜的脈遲條件下,鍍層結構能夠得到進一步的細化,從而穫得緻密、平整、均勻、光亮的鍍層,且鍍層與銅基體結閤良好.
채용맥충전도방법재자동편표면제비균균광량광활적얼도층.차조소묘전자현미경(SEM)진행분석,병대기도층결합력、공극솔、내마성등측시고찰도층성능화결구.위획취최괄의적공예삼수,연구맥충온도、평균전류밀도、점공비대얼도층현미경도적영향.통과마손실중측시,맥충전도얼도층적내마성능원원고우직류얼도층.최가공예조건위:류산얼300 g/L、록화얼50 g/L、붕산40 g/L、평균전류밀도위3 A/dm2、점공비위50%、도액온도위40~60℃.결과표명:재괄의적맥충조건하,도층결구능구득도진일보적세화,종이획득치밀、평정、균균、광량적도층,차도층여동기체결합량호.