现代涂料与涂装
現代塗料與塗裝
현대도료여도장
MODERN PAINT & FINISHING
2014年
9期
16-19,26
,共5页
环氧酯%酯化反应%酯化度%室温自交联
環氧酯%酯化反應%酯化度%室溫自交聯
배양지%지화반응%지화도%실온자교련
通过不饱和脂肪酸与环氧树脂分子链上的环氧基及羟基发生部分或全部酯化反应,制备出不同酯化度的室温自交联型环氧酯,探讨了不同催化剂用量和酯化温度对酯化反应的影响,考察了不同酯化度环氧酯的酯化反应时间及其物理化学性能.结果表明,环氧酯的酯化度越高,反应达到终点需要的时间也越长.酯化反应的最佳条件是催化剂用量占环氧树脂总量的1%,酯化温度为200℃.在此条件下,当环氧树脂上的所有羟基与亚麻油酸完全反应时,即酯化度为100%时需要9h.随着酯化度的增加,涂膜的干燥速度也越快,交联密度也越高,环氧酯涂膜的物理化学性能会有所提升.但并非酯化度越高环氧酯的涂膜性能也越好,酯化度过高,达100%时,涂膜性能反而会降低.综合考虑酯化度对产品性能的影响,酯化度宜定在80%.
通過不飽和脂肪痠與環氧樹脂分子鏈上的環氧基及羥基髮生部分或全部酯化反應,製備齣不同酯化度的室溫自交聯型環氧酯,探討瞭不同催化劑用量和酯化溫度對酯化反應的影響,攷察瞭不同酯化度環氧酯的酯化反應時間及其物理化學性能.結果錶明,環氧酯的酯化度越高,反應達到終點需要的時間也越長.酯化反應的最佳條件是催化劑用量佔環氧樹脂總量的1%,酯化溫度為200℃.在此條件下,噹環氧樹脂上的所有羥基與亞痳油痠完全反應時,即酯化度為100%時需要9h.隨著酯化度的增加,塗膜的榦燥速度也越快,交聯密度也越高,環氧酯塗膜的物理化學性能會有所提升.但併非酯化度越高環氧酯的塗膜性能也越好,酯化度過高,達100%時,塗膜性能反而會降低.綜閤攷慮酯化度對產品性能的影響,酯化度宜定在80%.
통과불포화지방산여배양수지분자련상적배양기급간기발생부분혹전부지화반응,제비출불동지화도적실온자교련형배양지,탐토료불동최화제용량화지화온도대지화반응적영향,고찰료불동지화도배양지적지화반응시간급기물이화학성능.결과표명,배양지적지화도월고,반응체도종점수요적시간야월장.지화반응적최가조건시최화제용량점배양수지총량적1%,지화온도위200℃.재차조건하,당배양수지상적소유간기여아마유산완전반응시,즉지화도위100%시수요9h.수착지화도적증가,도막적간조속도야월쾌,교련밀도야월고,배양지도막적물이화학성능회유소제승.단병비지화도월고배양지적도막성능야월호,지화도과고,체100%시,도막성능반이회강저.종합고필지화도대산품성능적영향,지화도의정재80%.