武钢技术
武鋼技術
무강기술
WUHAN IRON AND STEEL CORPORATION TECHNOLOGY
2014年
4期
19-21
,共3页
朱敏%任安超%费俊杰%吉玉%郑建国
硃敏%任安超%費俊傑%吉玉%鄭建國
주민%임안초%비준걸%길옥%정건국
U68CuCr钢轨%闪光焊%工艺
U68CuCr鋼軌%閃光銲%工藝
U68CuCr강궤%섬광한%공예
rail of U68CuCr%flash butt welding%process
耐蚀钢轨U68CuCr是新研发的钢轨品种,通过对预热闪光焊接工艺研究,制定出100 m耐蚀钢轨闪光焊接工艺。根据试验结果可以得出,当焊接热输入量在6600~6700 kJ,预热达到10次,预热峰值短路电流71.3 kA,短路时间3~4 s,快闪时间1.2~1.5 s,顶锻力达到420 kN,顶锻量为11~12 mm,焊接总耗时130 s,焊接后的钢轨焊头各项性能满足 TB/T 1632-2005《钢轨焊接》的要求。按照该闪光焊工艺焊接的钢轨,已在京广铁路上使用。
耐蝕鋼軌U68CuCr是新研髮的鋼軌品種,通過對預熱閃光銲接工藝研究,製定齣100 m耐蝕鋼軌閃光銲接工藝。根據試驗結果可以得齣,噹銲接熱輸入量在6600~6700 kJ,預熱達到10次,預熱峰值短路電流71.3 kA,短路時間3~4 s,快閃時間1.2~1.5 s,頂鍛力達到420 kN,頂鍛量為11~12 mm,銲接總耗時130 s,銲接後的鋼軌銲頭各項性能滿足 TB/T 1632-2005《鋼軌銲接》的要求。按照該閃光銲工藝銲接的鋼軌,已在京廣鐵路上使用。
내식강궤U68CuCr시신연발적강궤품충,통과대예열섬광한접공예연구,제정출100 m내식강궤섬광한접공예。근거시험결과가이득출,당한접열수입량재6600~6700 kJ,예열체도10차,예열봉치단로전류71.3 kA,단로시간3~4 s,쾌섬시간1.2~1.5 s,정단력체도420 kN,정단량위11~12 mm,한접총모시130 s,한접후적강궤한두각항성능만족 TB/T 1632-2005《강궤한접》적요구。안조해섬광한공예한접적강궤,이재경엄철로상사용。
Corrosion resistance rail U68CuCr is a new product of rail.The flash butt welding process of 100 m corrosion resistance rail was confirmed via study on the process of preheat flash butt welding.It could be drawn a conclusion that when the heat input of welding was 6 600-6 700 kJ,the number of preheat was 10,the peak of preheat short-circuit current 7 1 .3 kA,the time of short circuit 3-4 s,the rapid flash time 1 .2-1.5 s,the force of forge up to 420 kN,the distance of forge 11-12 mm,and total time of welding 130 s.The performance index of welding joint was satisfied with TB/T 1632-2005"welding of rail".The rail welded by this flash butt welding process has been used in j ing-guang railway.