施工技术
施工技術
시공기술
CONSTRUCTION TECHNOLOGY
2014年
15期
71-74
,共4页
霍晓敏%全理%周百先%唐清山
霍曉敏%全理%週百先%唐清山
곽효민%전리%주백선%당청산
钢筋%焊接%高强抗震钢筋%电渣压力焊%对比%试验
鋼觔%銲接%高彊抗震鋼觔%電渣壓力銲%對比%試驗
강근%한접%고강항진강근%전사압력한%대비%시험
steel bars%welding%high-strength seismic steel bars%electroslag welding%comparison%tests
随着HRB500E高强抗震钢筋的推广应用,国内各钢厂都相继研制出HRB500E高强抗震钢筋产品,通过对?22,?25的HRB500E高强抗震钢筋母材和焊接接头进行对比试验,分析HRB500E高强抗震钢筋电渣压力焊性能。试验结果证明,HRB500E钢筋可以进行电渣压力焊,施工中应按照“小电流、短电渣时间”的工艺特点,降低接头过热倾向。当钢筋母材实测抗拉强度小于1?12倍抗拉强度标准值,或在1?12倍标准值附近时,进行电渣压力焊后接头质量较易满足标准要求。
隨著HRB500E高彊抗震鋼觔的推廣應用,國內各鋼廠都相繼研製齣HRB500E高彊抗震鋼觔產品,通過對?22,?25的HRB500E高彊抗震鋼觔母材和銲接接頭進行對比試驗,分析HRB500E高彊抗震鋼觔電渣壓力銲性能。試驗結果證明,HRB500E鋼觔可以進行電渣壓力銲,施工中應按照“小電流、短電渣時間”的工藝特點,降低接頭過熱傾嚮。噹鋼觔母材實測抗拉彊度小于1?12倍抗拉彊度標準值,或在1?12倍標準值附近時,進行電渣壓力銲後接頭質量較易滿足標準要求。
수착HRB500E고강항진강근적추엄응용,국내각강엄도상계연제출HRB500E고강항진강근산품,통과대?22,?25적HRB500E고강항진강근모재화한접접두진행대비시험,분석HRB500E고강항진강근전사압력한성능。시험결과증명,HRB500E강근가이진행전사압력한,시공중응안조“소전류、단전사시간”적공예특점,강저접두과열경향。당강근모재실측항랍강도소우1?12배항랍강도표준치,혹재1?12배표준치부근시,진행전사압력한후접두질량교역만족표준요구。
With the popularization and application of high-strength seismic HRB500E steel bars, the corresponding products are constantly developed in China. Through the comparison test on base material and welded joints for HRB500E steel bars with 22mm and 25mm in diameter, the electroslag welding performance is analyzed. The test results prove that HRB500E steel bars can be connected with electroslag welding technology, and its construction should be in accordance with the small current, short electroslag time process characteristics to reduce joint overheating tendencies. When the tensile strength of steel base material is less than or in the vicinity of 1?12 times of the standard tensile strength, the quality of welding electroslag welding joint can easily meet the requirements of standard.