金属制品
金屬製品
금속제품
STEEL WIRE PRODUCTS
2014年
4期
48-51
,共4页
MG500锚杆钢筋%冶炼%轧制%化学成分%力学性能%金相组织
MG500錨桿鋼觔%冶煉%軋製%化學成分%力學性能%金相組織
MG500묘간강근%야련%알제%화학성분%역학성능%금상조직
MG500 bar for anchor rod%smelt%roll%chemical composition%mechanical property%microstructure
介绍MG500锚杆用热轧带肋钢筋研制开发过程.冶炼终点控制w(P)≤0.030%、w(C) ≥0.08%,出钢温度不低于1 620℃;LF炉精炼时间不少于40 min,白渣保持时间不低于15 min,软搅拌时间不低于10 min;连铸采用全程保护浇注,过热度不大于35℃,拉速稳定在(3.2±0.2) m/min,并采用结晶器电磁搅拌和液面自动控制技术;开轧温度为1 050 ~1 150 ℃,终轧为950 ~1 000℃.生产的(O)20 mm、(O)22 mm钢筋抗拉强度652 ~755 MPa,断后伸长率19% ~23%,钢筋弯曲试验无裂纹;产品金相组织为珠光体+铁素体,完全满足井下支护使用要求.
介紹MG500錨桿用熱軋帶肋鋼觔研製開髮過程.冶煉終點控製w(P)≤0.030%、w(C) ≥0.08%,齣鋼溫度不低于1 620℃;LF爐精煉時間不少于40 min,白渣保持時間不低于15 min,軟攪拌時間不低于10 min;連鑄採用全程保護澆註,過熱度不大于35℃,拉速穩定在(3.2±0.2) m/min,併採用結晶器電磁攪拌和液麵自動控製技術;開軋溫度為1 050 ~1 150 ℃,終軋為950 ~1 000℃.生產的(O)20 mm、(O)22 mm鋼觔抗拉彊度652 ~755 MPa,斷後伸長率19% ~23%,鋼觔彎麯試驗無裂紋;產品金相組織為珠光體+鐵素體,完全滿足井下支護使用要求.
개소MG500묘간용열알대륵강근연제개발과정.야련종점공제w(P)≤0.030%、w(C) ≥0.08%,출강온도불저우1 620℃;LF로정련시간불소우40 min,백사보지시간불저우15 min,연교반시간불저우10 min;련주채용전정보호요주,과열도불대우35℃,랍속은정재(3.2±0.2) m/min,병채용결정기전자교반화액면자동공제기술;개알온도위1 050 ~1 150 ℃,종알위950 ~1 000℃.생산적(O)20 mm、(O)22 mm강근항랍강도652 ~755 MPa,단후신장솔19% ~23%,강근만곡시험무렬문;산품금상조직위주광체+철소체,완전만족정하지호사용요구.