机床与液压
機床與液壓
궤상여액압
MACHINE TOOL & HYDRAULICS
2014年
16期
82-85
,共4页
王超%李明%刘廷峰%梁伟%李啸南%张卫东%逯国成
王超%李明%劉廷峰%樑偉%李嘯南%張衛東%逯國成
왕초%리명%류정봉%량위%리소남%장위동%록국성
恒流阀%恒流特性%FLUENT数值模拟
恆流閥%恆流特性%FLUENT數值模擬
항류벌%항류특성%FLUENT수치모의
Permanent flow valve%Constant-flow characteristics%FLUENT numerical simulation
胜利油田具有丰富的稠油资源,为了提高蒸汽吞吐采收率,根据分层注汽工艺原理设计的可控定量配注器可以实现分层注汽工艺技术的可控定量要求。为进一步认识可控定量配注器恒流阀阀内流场和确定维持恒流的压差范围,利用FLUENT流体力学软件对恒流阀内流场进行了数值模拟研究。研究结果表明:对于流体介质为水的阀内流动,最高流速出现在浮子与固定孔板之间的缝隙处,且在缝隙下游形成回流,下游区域发生流体分离现象,形成两个旋涡,消耗了主流运动的能量,导致压降和能量的降低;维持恒定流量Q=0.5 m3/h所需出、入口压差Δp在900~7400 Pa之间。
勝利油田具有豐富的稠油資源,為瞭提高蒸汽吞吐採收率,根據分層註汽工藝原理設計的可控定量配註器可以實現分層註汽工藝技術的可控定量要求。為進一步認識可控定量配註器恆流閥閥內流場和確定維持恆流的壓差範圍,利用FLUENT流體力學軟件對恆流閥內流場進行瞭數值模擬研究。研究結果錶明:對于流體介質為水的閥內流動,最高流速齣現在浮子與固定孔闆之間的縫隙處,且在縫隙下遊形成迴流,下遊區域髮生流體分離現象,形成兩箇鏇渦,消耗瞭主流運動的能量,導緻壓降和能量的降低;維持恆定流量Q=0.5 m3/h所需齣、入口壓差Δp在900~7400 Pa之間。
성리유전구유봉부적주유자원,위료제고증기탄토채수솔,근거분층주기공예원리설계적가공정량배주기가이실현분층주기공예기술적가공정량요구。위진일보인식가공정량배주기항류벌벌내류장화학정유지항류적압차범위,이용FLUENT류체역학연건대항류벌내류장진행료수치모의연구。연구결과표명:대우류체개질위수적벌내류동,최고류속출현재부자여고정공판지간적봉극처,차재봉극하유형성회류,하유구역발생류체분리현상,형성량개선와,소모료주류운동적능량,도치압강화능량적강저;유지항정류량Q=0.5 m3/h소수출、입구압차Δp재900~7400 Pa지간。
Shengli oilfield has rich resource of thickene d oil.In order to improve the recovery ratio of steam huff and puff,the controllable quantitative requirement of layering steam injection technology can be realized by the controllable quantitative injection allo-cator designed according to the principle of layering steam injection technology.In order to further understand the flow inside the valve and confirm the pressure differential range required for maintaining the constant flow,FLUENT hydromechanics software was applied to conduct the numerical simulation study of the internal flow field of permanent flow valve.The research results show that as for the flow inside valve with the fluid medium of water,the peak flow rate occurs at the gap between the floater and fixed pore plate;and under this gap,the backflow is formed.The fluidic divergence phenomenon occurs in the downstream area;two swirls are formed and con-sume the energy of mainstream movement,which will lead to the pressure drop and energy reduction.The variation range of outlet and inlet differential pressure (Δp)required for maintaining the constant flow rate (Q=0.5 m3/h)is 900~7 400 Pa.