电镀与精饰
電鍍與精飾
전도여정식
PLATING & FINISHING
2014年
10期
43-46
,共4页
重金属捕集剂%丁基黄药%硫化钠%电镀工业废水
重金屬捕集劑%丁基黃藥%硫化鈉%電鍍工業廢水
중금속포집제%정기황약%류화납%전도공업폐수
heavy metal chelating agent%butyl xanthate%sodium sulfide%electroplating wastewater
研究了重金属捕集剂丁基黄药处理电镀工业废水的工艺条件.实验结果表明,在常温下,将电镀废水的pH由2.9调至6~7,加入2.5 mL 10%的丁基黄药溶液.絮凝剂0.8mL0.1%的聚合氯化铝溶液,快速搅拌(300 r/min)1 min,慢速搅拌(100 r/min) 10min,处理后的废水中Cu2+、Zn2、Ni2+、Cr(Ⅵ)和总铬等重金属离子的残留质量浓度均低于国家电镀污染物排放标准(GB21900-2008)最高允许值,产生的污泥在pH大于或等于9的水环境中比较稳定.与硫化钠处理电镀废水比较,该方法沉降速度快、矾花大、污泥体积小,污泥可以回收利用,具有良好的应用前景.
研究瞭重金屬捕集劑丁基黃藥處理電鍍工業廢水的工藝條件.實驗結果錶明,在常溫下,將電鍍廢水的pH由2.9調至6~7,加入2.5 mL 10%的丁基黃藥溶液.絮凝劑0.8mL0.1%的聚閤氯化鋁溶液,快速攪拌(300 r/min)1 min,慢速攪拌(100 r/min) 10min,處理後的廢水中Cu2+、Zn2、Ni2+、Cr(Ⅵ)和總鉻等重金屬離子的殘留質量濃度均低于國傢電鍍汙染物排放標準(GB21900-2008)最高允許值,產生的汙泥在pH大于或等于9的水環境中比較穩定.與硫化鈉處理電鍍廢水比較,該方法沉降速度快、礬花大、汙泥體積小,汙泥可以迴收利用,具有良好的應用前景.
연구료중금속포집제정기황약처리전도공업폐수적공예조건.실험결과표명,재상온하,장전도폐수적pH유2.9조지6~7,가입2.5 mL 10%적정기황약용액.서응제0.8mL0.1%적취합록화려용액,쾌속교반(300 r/min)1 min,만속교반(100 r/min) 10min,처리후적폐수중Cu2+、Zn2、Ni2+、Cr(Ⅵ)화총락등중금속리자적잔류질량농도균저우국가전도오염물배방표준(GB21900-2008)최고윤허치,산생적오니재pH대우혹등우9적수배경중비교은정.여류화납처리전도폐수비교,해방법침강속도쾌、반화대、오니체적소,오니가이회수이용,구유량호적응용전경.