天津工业大学学报
天津工業大學學報
천진공업대학학보
JOURNAL OF TIANJIN POLYTECHNIC UNIVERSITY
2014年
5期
8-13
,共6页
焦亚男%祁小芬%吴宁%崔萍
焦亞男%祁小芬%吳寧%崔萍
초아남%기소분%오저%최평
亚麻%聚丙烯%复合材料%模压成型%拉伸性能%顶破性能
亞痳%聚丙烯%複閤材料%模壓成型%拉伸性能%頂破性能
아마%취병희%복합재료%모압성형%랍신성능%정파성능
flax%polypropylene%composites%molding process%tensile properties%bursting properties
以亚麻纤维作为增强纤维,以聚丙烯纤维作为树脂基体,通过模压成型工艺方法,制备了绿色环保型亚麻/聚丙烯复合材料,主要研究了纤维长度、模压温度及保温时间对复合材料拉伸性能及顶破性能的影响。结果表明:模压温度对复合材料性能的影响最显著;当纤维长度为5 mm、模压温度为180℃、保温时间为40 min时,复合材料的拉伸性能最优;在纤维长度为5 mm、模压温度为170℃、保温时间为40 min 时,复合材料的耐顶破性能最优。
以亞痳纖維作為增彊纖維,以聚丙烯纖維作為樹脂基體,通過模壓成型工藝方法,製備瞭綠色環保型亞痳/聚丙烯複閤材料,主要研究瞭纖維長度、模壓溫度及保溫時間對複閤材料拉伸性能及頂破性能的影響。結果錶明:模壓溫度對複閤材料性能的影響最顯著;噹纖維長度為5 mm、模壓溫度為180℃、保溫時間為40 min時,複閤材料的拉伸性能最優;在纖維長度為5 mm、模壓溫度為170℃、保溫時間為40 min 時,複閤材料的耐頂破性能最優。
이아마섬유작위증강섬유,이취병희섬유작위수지기체,통과모압성형공예방법,제비료록색배보형아마/취병희복합재료,주요연구료섬유장도、모압온도급보온시간대복합재료랍신성능급정파성능적영향。결과표명:모압온도대복합재료성능적영향최현저;당섬유장도위5 mm、모압온도위180℃、보온시간위40 min시,복합재료적랍신성능최우;재섬유장도위5 mm、모압온도위170℃、보온시간위40 min 시,복합재료적내정파성능최우。
Eco-environment flax/ polypropylene thermoplastic composite are prepared by compression molding process, in which the flax fibers as reinforcement and the matrix phases are come from polypropylene (PP) fibers. The effects of fiber length, molded temperature and holding time on the tensile and bursting performance of the composites are investigated. The results show that the molding temperature was the main factor to influence composite properties. The optimal tensile property of the flax/polypropylene composite is obtained in the parameters of fiber length 5 mm, molding temperature 180 ℃ and holding time 40 min. The bursting performance of the polypropylene/flax composites is come to the peak value when mentioned above parameters are 5 mm, 170 ℃ and 40 min.