机床与液压
機床與液壓
궤상여액압
MACHINE TOOL & HYDRAULICS
2014年
19期
159-162
,共4页
赵大兴%王婷%赵迪%丁国龙
趙大興%王婷%趙迪%丁國龍
조대흥%왕정%조적%정국룡
磨齿机%主轴系统%模态分析%动态特性%Workbench
磨齒機%主軸繫統%模態分析%動態特性%Workbench
마치궤%주축계통%모태분석%동태특성%Workbench
Gear grinding machine%Spindle system%Model analysis%Dynamic characteristics%Workbench
主轴系统是磨齿机的重要组成部分,主轴的动态特性对齿轮的磨削精度与生产效率有着很大的影响。以磨齿机的主轴系统为研究对象,在SolidWorks中建立模型,并通过有限元软件Workbench对其进行模态分析,得出了主轴系统的固有频率和最大偏振量。分析了主轴系统在不同跨距和不同主轴材料弹性模量等条件下对主轴动态特性的影响。结果表明:1023号碳板钢的最大变形量相对较小,可作为主轴材料;模态频率随支承间距的增加而提高;主轴系统的最大变形量随支承间距的增加减小,最佳支承间距为240 mm。
主軸繫統是磨齒機的重要組成部分,主軸的動態特性對齒輪的磨削精度與生產效率有著很大的影響。以磨齒機的主軸繫統為研究對象,在SolidWorks中建立模型,併通過有限元軟件Workbench對其進行模態分析,得齣瞭主軸繫統的固有頻率和最大偏振量。分析瞭主軸繫統在不同跨距和不同主軸材料彈性模量等條件下對主軸動態特性的影響。結果錶明:1023號碳闆鋼的最大變形量相對較小,可作為主軸材料;模態頻率隨支承間距的增加而提高;主軸繫統的最大變形量隨支承間距的增加減小,最佳支承間距為240 mm。
주축계통시마치궤적중요조성부분,주축적동태특성대치륜적마삭정도여생산효솔유착흔대적영향。이마치궤적주축계통위연구대상,재SolidWorks중건립모형,병통과유한원연건Workbench대기진행모태분석,득출료주축계통적고유빈솔화최대편진량。분석료주축계통재불동과거화불동주축재료탄성모량등조건하대주축동태특성적영향。결과표명:1023호탄판강적최대변형량상대교소,가작위주축재료;모태빈솔수지승간거적증가이제고;주축계통적최대변형량수지승간거적증가감소,최가지승간거위240 mm。
Spindle system is an important part of grinding machine,which dynamic characteristics have a great impact on the grinding precision and production efficiency of gear. To make the grinding machine spindle system as the research object,a finite ele-ment model (FEM)was established on SolidWorks,and through the finite element software Workbench to do modal analysis,and then the natural frequency of the spindle system and maximum polarization were obtained. The impact on the dynamic characteristics of the spindle was analyzed when it was under the condition of different span,different elastic modulus of spindle material and so on. The re-sults show that the largest deformation of carbon steel plate of 1023#is relatively small,which can be used as spindle materials;Modal frequencies increase with the increasing of bearing spacing. The maximum deformation of spindle system decreases with the increasing of bearing spacing and the best supporting spacing is 240 mm.