电源技术
電源技術
전원기술
CHINESE JOURNAL OF POWER SOURCES
2014年
11期
2003-2006
,共4页
范留飞%谈金祝%胡学家%周靖%张旭
範留飛%談金祝%鬍學傢%週靖%張旭
범류비%담금축%호학가%주정%장욱
气体扩散层%孔隙率%封装力%有限元方法
氣體擴散層%孔隙率%封裝力%有限元方法
기체확산층%공극솔%봉장력%유한원방법
GDL%porosity%assembly force%finite element method
质子交换膜(PEM)燃料电池中气体扩散层(GDL)的孔隙率对整个燃料电池的性能有着重要影响,而封装力是影响燃料电池GDL孔隙率的关键因素之一。采用实验和有限元模拟相结合的方法研究封装力对气体扩散层孔隙率的影响。利用压汞仪测试气体扩散层的平均孔隙率,基于有限元方法建立质子交换膜燃料电池的双极板和气体扩散层的接触模型,研究质子交换膜燃料电池中不同的封装力下气体扩散层的孔隙率变化情况。结果表明:气体扩散层孔隙率的变化沿接触中心线左右对称,接触区域孔隙率分布较为均匀,随着封装力的增加,气体扩散层孔隙率逐渐降低;而未接触区域孔隙率变化不明显。气体扩散层孔隙率有限元模拟结果与实验测试结果相吻合。
質子交換膜(PEM)燃料電池中氣體擴散層(GDL)的孔隙率對整箇燃料電池的性能有著重要影響,而封裝力是影響燃料電池GDL孔隙率的關鍵因素之一。採用實驗和有限元模擬相結閤的方法研究封裝力對氣體擴散層孔隙率的影響。利用壓汞儀測試氣體擴散層的平均孔隙率,基于有限元方法建立質子交換膜燃料電池的雙極闆和氣體擴散層的接觸模型,研究質子交換膜燃料電池中不同的封裝力下氣體擴散層的孔隙率變化情況。結果錶明:氣體擴散層孔隙率的變化沿接觸中心線左右對稱,接觸區域孔隙率分佈較為均勻,隨著封裝力的增加,氣體擴散層孔隙率逐漸降低;而未接觸區域孔隙率變化不明顯。氣體擴散層孔隙率有限元模擬結果與實驗測試結果相吻閤。
질자교환막(PEM)연료전지중기체확산층(GDL)적공극솔대정개연료전지적성능유착중요영향,이봉장력시영향연료전지GDL공극솔적관건인소지일。채용실험화유한원모의상결합적방법연구봉장력대기체확산층공극솔적영향。이용압홍의측시기체확산층적평균공극솔,기우유한원방법건립질자교환막연료전지적쌍겁판화기체확산층적접촉모형,연구질자교환막연료전지중불동적봉장력하기체확산층적공극솔변화정황。결과표명:기체확산층공극솔적변화연접촉중심선좌우대칭,접촉구역공극솔분포교위균균,수착봉장력적증가,기체확산층공극솔축점강저;이미접촉구역공극솔변화불명현。기체확산층공극솔유한원모의결과여실험측시결과상문합。
The porosity of the gas diffusion layer (GDL) in proton exchange membrane (PEM) fuel cellhas a significant effect on PEM fuel cellperformance. Assembly force was critical to the porosity of the GDL. Based on both experimental and finite element methods, the influence of assembly force on porosity of the GDL was studied. The mercury porosimeter was employed to measure the average porosity of the GDL. The contact model between bipolar plate (BPP) and GDL of the PEM fuel cellwas established, and finite element method (FEM) was used to study the variation of porosity of the GDL applied with various assembly forces. The simulated results show that the variation of porosity of the GDL was symmetrical along with the center line of the contact area. The porosity distribution in GDL was uniform at the area where GDL contacted with BPP under the applied assembly force. And the porosity of the GDL was decreased gradual y with the increase of the assembly force. However, the porosity was not change significantly at the area where GDL did not contact with BPP. The finite element analysis results were in good agreement with the experimental results in average porosity.