功能材料
功能材料
공능재료
JOURNAL OF FUNCTIONAL MATERIALS
2012年
11期
1509-1512
,共4页
共沉淀预烧粉%MnZn高导铁氧体%烧结%磁性能
共沉澱預燒粉%MnZn高導鐵氧體%燒結%磁性能
공침정예소분%MnZn고도철양체%소결%자성능
coprecipitation-preroasting powders%Mn-Zn high initial permeability ferrite%sintering%magnetic property
以共沉淀法预烧粉为原料,研究了烧结温度及烧结气氛对MnZn高导铁氧体磁性能的影响,采用SEM对其微观结构进行了表征。结果表明,随着烧结温度升高,MnZn高导铁氧体的μi增加;合适的烧结条件能促进晶粒生长,减少气孔产生,增大烧结密度,使晶界变细,提高初始磁导率和改善频率特性。当温度为1380℃,保温气氛为3.0%时,MnZn高导铁氧体的μi为13000,且有较好的频率特性,在150kHz时μi能维持在10000以上。
以共沉澱法預燒粉為原料,研究瞭燒結溫度及燒結氣氛對MnZn高導鐵氧體磁性能的影響,採用SEM對其微觀結構進行瞭錶徵。結果錶明,隨著燒結溫度升高,MnZn高導鐵氧體的μi增加;閤適的燒結條件能促進晶粒生長,減少氣孔產生,增大燒結密度,使晶界變細,提高初始磁導率和改善頻率特性。噹溫度為1380℃,保溫氣氛為3.0%時,MnZn高導鐵氧體的μi為13000,且有較好的頻率特性,在150kHz時μi能維持在10000以上。
이공침정법예소분위원료,연구료소결온도급소결기분대MnZn고도철양체자성능적영향,채용SEM대기미관결구진행료표정。결과표명,수착소결온도승고,MnZn고도철양체적μi증가;합괄적소결조건능촉진정립생장,감소기공산생,증대소결밀도,사정계변세,제고초시자도솔화개선빈솔특성。당온도위1380℃,보온기분위3.0%시,MnZn고도철양체적μi위13000,차유교호적빈솔특성,재150kHz시μi능유지재10000이상。
The influence of sintering conditions on the magnetic properties of MnZn high initial permeability ferrite from coprecipitation-preroasting powders were studied and phase composition and microstructure of samples were investigated by XRD and SEM.The results show that the initial permeability increase,with the increased sintering temperature,and an increase of its frequency characteristic with increasing oxygen partial pressure is observed.When the sintering temperature is 1380℃ and the oxygen partial pressure is 3.5%,all the magnetic properties come to the best.The initial permeability can reach more than 13000 and is mainly unchanged to 150kHz.The study indicates that appropriate sintering conditions can promote the growth of gains,reduce the amount of pores,increase the sintering density and coercive force,the grain boundary became thinner,consequently increase initial permeability and improve the frequency characteristics.