CAJ | 학술논문

该文针对新疆地区吊篮式移栽机手工喂入效率低的问题,设计了穴盘苗移栽自动取喂系统.该系统采用穴盘步进移位机构提供穴盘的横向和纵向移位,由翻转摆位式取苗机械手进行取苗和穴盘苗的转移,利用柔性链输送喂入机构对穴盘苗逐个投放,能够对穴高45 mm、上边宽31.75 mm、下边宽13 mm的吸塑成型的软穴盘苗进行自动取苗并向两个栽植器投苗.整个系统由PLC(programmable logic controller)程序控制,采用气压驱动,工作气压0.5~0.8 MPa,耗气量60.65 L/min,单组取喂系统结构独立,质量小于110 kg,不增加原有移栽机地轮负荷,即能与新移栽机配套生产,也能对现有移栽机进行自动化改造.系统中穴盘步进移位机构在柔性链输送喂入机构的侧上方倾斜放置,使穴盘上表面与水平面的夹角105°,缩小了机器水平占用空间.采用苗龄58 d的“红安6号”辣椒苗进行室内取苗试验,试验结果显示,系统取喂苗总可靠率达98.92%,平均基质损失质量9.26%,取喂速度达70株/min,未见明显伤苗,能够满足设计要求.
해문침대신강지구조람식이재궤수공위입효솔저적문제,설계료혈반묘이재자동취위계통.해계통채용혈반보진이위궤구제공혈반적횡향화종향이위,유번전파위식취묘궤계수진행취묘화혈반묘적전이,이용유성련수송위입궤구대혈반묘축개투방,능구대혈고45 mm、상변관31.75 mm、하변관13 mm적흡소성형적연혈반묘진행자동취묘병향량개재식기투묘.정개계통유PLC(programmable logic controller)정서공제,채용기압구동,공작기압0.5~0.8 MPa,모기량60.65 L/min,단조취위계통결구독립,질량소우110 kg,불증가원유이재궤지륜부하,즉능여신이재궤배투생산,야능대현유이재궤진행자동화개조.계통중혈반보진이위궤구재유성련수송위입궤구적측상방경사방치,사혈반상표면여수평면적협각105°,축소료궤기수평점용공간.채용묘령58 d적“홍안6호”랄초묘진행실내취묘시험,시험결과현시,계통취위묘총가고솔체98.92%,평균기질손실질량9.26%,취위속도체70주/min,미견명현상묘,능구만족설계요구.
@@@@The nacelle-type semi-automatic transplanter is the best available technology to punch holes in the plastic film and has been used extensively in Xinjiang, China, but the nacelle-type transplanter had very low efficiency. It had the frequency of less than 40 pieces /min for each transplanting device. The automatic feed system was designed for a nacelle-type transplanter to improve the efficiency of the feeding system of the transplanter, matching with the tray which is widely used in Xinjiang province. It has 128 (16 rows×8 lines) plugs and is made by the vacuum form process. The thickness is 0.6-1 mm, the hole depth is 45 mm, the top width is 31.75mm and the bottom width is 13mm. The tray carrying the seedlings can be moved transversally and longitudinally by the step-displacement unit (SDU) in the feed system. In order to reduce the automatic feed system width of the horizontal direction, and keep plug seedlings from dropping from the plug tray, the machine was slanted at an angle horizontally with the SDU beams at 105° . The seedlings were taken and moved by a turning and position shift style seedlings manipulator (TPSM). The seedlings were dropped in the tube of the flexible chain conveyor feeding mechanism (FCCFM) by the manipulator at the right time. Then the seedlings were transported and put in the nacelle of two different transplanting devices by the FCCFM. The FCCFM was set at the bottom of the feed system. The SDU was set on the top and side of FCCFM, and the TPSM was set on the top of the FCCFM. The seedling transfer was done by the TPSM, which picks up the seedling on the tray side and drops the seedlings on the other side. When the seedling tube is standing still, the manipulator puts the plug seedlings into the seedling tube. With the seedlings tube driven by the flexible chain and rotating to the right side, the seedling tube will go through two types of drop windows--one is wide, and the other is narrow. When the seedlings tube first goes through the narrow drop seedlings window, only the narrow shutter of the seedling tube is opened and drops seedlings. When the seedlings tube goes through the wide drop seedlings window, all the shutters open, and only the wide shutter seedling tube drops seedlings. The feed system is controlled by PLC, and driven by pneumatic force. The average total air consumption of the pneumatic components is 60.56L/min. The structure of this automatic feed system is independent and does not increase the load on the wheels of the transplanting machine. Its mass is less than 110kg and the cost is also affordable. It can be attached to a new transplanting machine or it can be used with an existing transplanting machine. The “Hong'an #6”pepper seedlings were used to test the automatic feed system, and seedlings were raised from February 25, 2011 to April 25, 2011. At a seedling age of 58d, the average height of the seedlings was 163.06mm;nursery substrates were made of peat, vermiculite and perlite, in accordance with the volume ratio 1:1:1. Compressed air is provided by the laboratory air pump (ZBM-0.1/8), and the air tank pressure was maintained at 0.5 ~ 0.8MPa. The results showed that the seedling feeding speed was increased up to 70pieces/min, the reliability of the system was 98.92%, and the average mass loss of the seedling substrate was 9.26%.