燃气涡轮试验与研究
燃氣渦輪試驗與研究
연기와륜시험여연구
GAS TURBINE EXPERIMENT AND RESEARCH
2013年
2期
54-58
,共5页
郭梅%陈聪慧%战鹏%曹璨%李博
郭梅%陳聰慧%戰鵬%曹璨%李博
곽매%진총혜%전붕%조찬%리박
航空发动机%中央传动杆%中间轴承%临界转速%故障分析
航空髮動機%中央傳動桿%中間軸承%臨界轉速%故障分析
항공발동궤%중앙전동간%중간축승%림계전속%고장분석
aero-engine%radial driving shaft%middle bearing%critical speed%failure analysis
针对某型发动机试车中反复出现中央传动杆中间轴承滚子和保持架脱落、内圈严重磨损故障,进行结构合理性分析、振动特性计算、实物测量、产品质量复查及相关试验测量,确定影响传动杆正常工作的各项因素,找出了传动杆破坏原因.采取传动杆轴径优化设计、改善供油、提高加工质量、改进安装形式等多项措施,解决磨损故障.改进后的发动机试车验证表明,传动杆工作稳定,效果良好.最后,总结出三支点细长中央传动杆设计的关键技术,可为同类中央传动杆设计提供借鉴.
針對某型髮動機試車中反複齣現中央傳動桿中間軸承滾子和保持架脫落、內圈嚴重磨損故障,進行結構閤理性分析、振動特性計算、實物測量、產品質量複查及相關試驗測量,確定影響傳動桿正常工作的各項因素,找齣瞭傳動桿破壞原因.採取傳動桿軸徑優化設計、改善供油、提高加工質量、改進安裝形式等多項措施,解決磨損故障.改進後的髮動機試車驗證錶明,傳動桿工作穩定,效果良好.最後,總結齣三支點細長中央傳動桿設計的關鍵技術,可為同類中央傳動桿設計提供藉鑒.
침대모형발동궤시차중반복출현중앙전동간중간축승곤자화보지가탈락、내권엄중마손고장,진행결구합이성분석、진동특성계산、실물측량、산품질량복사급상관시험측량,학정영향전동간정상공작적각항인소,조출료전동간파배원인.채취전동간축경우화설계、개선공유、제고가공질량、개진안장형식등다항조시,해결마손고장.개진후적발동궤시차험증표명,전동간공작은정,효과량호.최후,총결출삼지점세장중앙전동간설계적관건기술,가위동류중앙전동간설계제공차감.
For the driving shaft encountering the roller and retainer breaking off and inner spacers wearing out during the engine tests, the structure analyses, vibration calculation, component measurement, quality assessment and related tests were carried out. Finally the factors effecting the driving shaft operation and the reasons of failure were defined. Several measures including shaft diameter optimization, increasing oil supply, improving manufacture quality and installation form were taken to clear up the failures. After im?provement, the testing results showed that the driving shaft worked steadily and the effect was good. At last, the key technology of radial driving shaft with three supporting points is summarized, which has a great help for the driving shaft design.