光电工程
光電工程
광전공정
OPTO-ELECTRONIC ENGINEERING
2013年
2期
145-150
,共6页
胡新艳%刘金梅%李爱涛%霍文晓
鬍新豔%劉金梅%李愛濤%霍文曉
호신염%류금매%리애도%곽문효
CDMA%放大器%激光器%三阶交调截点%三阶交调产物
CDMA%放大器%激光器%三階交調截點%三階交調產物
CDMA%방대기%격광기%삼계교조절점%삼계교조산물
CDMA%amplifiers%laser%IP3%IM3
针对通信系统中CDMA光模块的非线性失真对整个系统性能的影响问题,本文从激光器和放大器两方面出发,通过采用三阶交调截点(IP3)和三阶交调产物(IM3)参数作为衡量CDMA光模块非线性失真的指标,详细地分析了光模块的失真特性,并在此基础上初步探讨了改善CDMA模块失真的基本方法,包括改变模块内部激光器的偏置电流,放大器的偏流及外围匹配电路在内的一系列方法.实验通过观察条件的改变对IP3和IM3的影响从而证实文中提出的方法行之有效,均能从一定程度上改善系统的失真指标.目前国内外对此类失真特性的研究一般集中在电性能上,对光器件与电器件相结合的研究涉及较少,本文提出的方法对实际商用化光模块产品有一定的借鉴意义,具有一定的使用价值.
針對通信繫統中CDMA光模塊的非線性失真對整箇繫統性能的影響問題,本文從激光器和放大器兩方麵齣髮,通過採用三階交調截點(IP3)和三階交調產物(IM3)參數作為衡量CDMA光模塊非線性失真的指標,詳細地分析瞭光模塊的失真特性,併在此基礎上初步探討瞭改善CDMA模塊失真的基本方法,包括改變模塊內部激光器的偏置電流,放大器的偏流及外圍匹配電路在內的一繫列方法.實驗通過觀察條件的改變對IP3和IM3的影響從而證實文中提齣的方法行之有效,均能從一定程度上改善繫統的失真指標.目前國內外對此類失真特性的研究一般集中在電性能上,對光器件與電器件相結閤的研究涉及較少,本文提齣的方法對實際商用化光模塊產品有一定的藉鑒意義,具有一定的使用價值.
침대통신계통중CDMA광모괴적비선성실진대정개계통성능적영향문제,본문종격광기화방대기량방면출발,통과채용삼계교조절점(IP3)화삼계교조산물(IM3)삼수작위형량CDMA광모괴비선성실진적지표,상세지분석료광모괴적실진특성,병재차기출상초보탐토료개선CDMA모괴실진적기본방법,포괄개변모괴내부격광기적편치전류,방대기적편류급외위필배전로재내적일계렬방법.실험통과관찰조건적개변대IP3화IM3적영향종이증실문중제출적방법행지유효,균능종일정정도상개선계통적실진지표.목전국내외대차류실진특성적연구일반집중재전성능상,대광기건여전기건상결합적연구섭급교소,본문제출적방법대실제상용화광모괴산품유일정적차감의의,구유일정적사용개치.
Nonlinear distortion of CDMA optical module has severely affected the whole system performance in a communication system, for the problem, by the use of IP3(the third-order Intercept point) and IM3(third-order intermodulation signal) parameters as an index of measuring CDMA optical module nonlinear distortion, and distortion properties of optical modules is analyzed in detail from two aspects including lasers and amplifiers. On this basis, basic methods to improve the CDMA module distortion are discussed preliminarily, such a series of methods as changes to module internal laser bias currents, amplifier bias currents and peripheral matching circuits, and etc. The experimental results demonstrate that the proposed method is effective, which can improve the system distortion index in a certain degree, by watching influence on IP3 and IM3 parameters when condition changes. At present, the research for such distortion characteristics generally concentrated on the electrics, less on the optical devices combined with electrical devices at home and abroad. The method has certain significance and value for actual commercial optical module products.