石油钻采工艺
石油鑽採工藝
석유찬채공예
OIL DRILLING & PRODUCTION TECHNOLOGY
2013年
1期
94-96
,共3页
王旱祥%刘延鑫%陈一男%兰文剑%孟繁宇
王旱祥%劉延鑫%陳一男%蘭文劍%孟繁宇
왕한상%류연흠%진일남%란문검%맹번우
二次射孔%筛管%强度%有限元%影响分析
二次射孔%篩管%彊度%有限元%影響分析
이차사공%사관%강도%유한원%영향분석
secondary perforation%screen pipe%strength%FEM%effects analysis
为了研究二次射孔对筛管剩余强度影响的变化规律,利用有限元分析软件ANSYS分别建立了井下二次射孔时新旧两孔处于两种不同情况下的有限元模型,模拟分析了二次射孔对筛管剩余强度的影响,研究结果表明:在进行二次射孔时,最佳射孔位置为中线附近区域,此时不仅能保证油气流通面积、提高采油效率,并且可以使筛管的剩余强度提高,达到了二次射孔的目的;在二次射孔时应尽量避免出现新孔与旧孔相交的情况,若不得已出现,要保证相交孔圆心角大于90°,并且随着圆心角的增大,筛管剩余强度也不断增大.
為瞭研究二次射孔對篩管剩餘彊度影響的變化規律,利用有限元分析軟件ANSYS分彆建立瞭井下二次射孔時新舊兩孔處于兩種不同情況下的有限元模型,模擬分析瞭二次射孔對篩管剩餘彊度的影響,研究結果錶明:在進行二次射孔時,最佳射孔位置為中線附近區域,此時不僅能保證油氣流通麵積、提高採油效率,併且可以使篩管的剩餘彊度提高,達到瞭二次射孔的目的;在二次射孔時應儘量避免齣現新孔與舊孔相交的情況,若不得已齣現,要保證相交孔圓心角大于90°,併且隨著圓心角的增大,篩管剩餘彊度也不斷增大.
위료연구이차사공대사관잉여강도영향적변화규률,이용유한원분석연건ANSYS분별건립료정하이차사공시신구량공처우량충불동정황하적유한원모형,모의분석료이차사공대사관잉여강도적영향,연구결과표명:재진행이차사공시,최가사공위치위중선부근구역,차시불부능보증유기류통면적、제고채유효솔,병차가이사사관적잉여강도제고,체도료이차사공적목적;재이차사공시응진량피면출현신공여구공상교적정황,약불득이출현,요보증상교공원심각대우90°,병차수착원심각적증대,사관잉여강도야불단증대.
?In?order?to?understand?the?effect?of?secondary?perforation?on?screen?pipe?strength,?the?finite?element?models?of?bullet?hole?were established with the help of software ANSYS when the positions of secondary and original perforation were different, and then the effect?of?secondary?perforation?on?the?residual?intensity?of?screen?pipe?was?analyzed.?The?results?show?that?the?best?position?for?secondary?perforation?is?regions?near?the?midline.?With?the?favorable?position,?large?oil?and?gas?flow?area?can?be?ensured?which?will?result?in?higher?oil?recovery?efficiency.?And?the?goals?of?secondary?perforation?can?be?met?by?enhancing?residual?intensity?of?screen?pipe.?At?the?same?time, the intersection of secondary and original perforation bullet hole should be avoided, if it can’t be avoided, the cross hole central angle?should?be?more?than?90?degree,?because?that?the?residual?strength?will?grow?with?the?increase?of?central?angle.