井冈山大学学报(自然科学版)
井岡山大學學報(自然科學版)
정강산대학학보(자연과학판)
JOURNAL OF JINGGANGSHAN UNIVERSITY(SCIENCE AND TECHNOLOGY)
2013年
1期
35-38
,共4页
罗志刚*%林俊岳%况生荣
囉誌剛*%林俊嶽%況生榮
라지강*%림준악%황생영
松香%连续法%EVA热熔胶
鬆香%連續法%EVA熱鎔膠
송향%련속법%EVA열용효
rosin%continuous method%EVA hot melt adhesive
以探讨松香连续法制备 EVA 热熔胶的可行性为目的,通过对比实验比较了连续法和分步法的优缺点,考察了连续法制胶中松香酯化的合理时间及松香与EVA合适的质量配比,结果表明,松香连续法制备EVA热熔胶在实验阶段是可行的;连续法所得热熔胶与分步法所制热熔胶相比有色泽浅、粘合力强的特点;在以ZnO(松香的0.3%)作催化剂、季戊四醇用量为松香的15%、复配抗氧剂用量为松香的0.2%、石蜡用量为 EVA 质量的10%、酯化温度为270℃、制胶温度为200℃的条件下,连续法制胶中松香酯化的合理时间为6~7 h,松香与EVA合适质量配比为30/50~40/50;在此工艺条件下制得了色泽淡黄、粘合强度为675 g、流动性为2.5 mm/10g的EVA热熔胶.
以探討鬆香連續法製備 EVA 熱鎔膠的可行性為目的,通過對比實驗比較瞭連續法和分步法的優缺點,攷察瞭連續法製膠中鬆香酯化的閤理時間及鬆香與EVA閤適的質量配比,結果錶明,鬆香連續法製備EVA熱鎔膠在實驗階段是可行的;連續法所得熱鎔膠與分步法所製熱鎔膠相比有色澤淺、粘閤力彊的特點;在以ZnO(鬆香的0.3%)作催化劑、季戊四醇用量為鬆香的15%、複配抗氧劑用量為鬆香的0.2%、石蠟用量為 EVA 質量的10%、酯化溫度為270℃、製膠溫度為200℃的條件下,連續法製膠中鬆香酯化的閤理時間為6~7 h,鬆香與EVA閤適質量配比為30/50~40/50;在此工藝條件下製得瞭色澤淡黃、粘閤彊度為675 g、流動性為2.5 mm/10g的EVA熱鎔膠.
이탐토송향련속법제비 EVA 열용효적가행성위목적,통과대비실험비교료련속법화분보법적우결점,고찰료련속법제효중송향지화적합리시간급송향여EVA합괄적질량배비,결과표명,송향련속법제비EVA열용효재실험계단시가행적;련속법소득열용효여분보법소제열용효상비유색택천、점합력강적특점;재이ZnO(송향적0.3%)작최화제、계무사순용량위송향적15%、복배항양제용량위송향적0.2%、석사용량위 EVA 질량적10%、지화온도위270℃、제효온도위200℃적조건하,련속법제효중송향지화적합리시간위6~7 h,송향여EVA합괄질량배비위30/50~40/50;재차공예조건하제득료색택담황、점합강도위675 g、류동성위2.5 mm/10g적EVA열용효.
The feasibility of EVA hot melt adhesive preparation by rosin continuous method was discussed in this paper. The advantages and disadvantages of continuous method and multistep method were compared by contrast experiments, reasonable time of rosin esterification and proper mass ratio of rosin with EVA were investigated in adhesive preparation by continuous method. The results show that it is feasible for EVA hot melt adhesive preparation by rosin continuous method in the experimental stage;compared with multistep method, the hot melt adhesive prepared by continuous method has the traits with light color and strong adhesion; 30/50~40/5 when ZnO (0.3%of rosin) is the catalyst, pentaerythritol amount is 15%of rosin, the dosage of compound antioxidant is 0.2% of rosin, paraffin quality is 10% of the EVA, the reaction temperature is 270 ℃ , the system rubber temperature is 200 ℃, the reasonable time of rosin esterification is 6 to 7 hours in adhesive preparation by continuous method, the suitable mass ratio of rosin with EVA is 30/50~40/50;EVA hot melt adhesive prepared in this process appeared the color of light yellow, bond strength of 675 g, fluidity of 2.5mm/10g.