噪声与振动控制
譟聲與振動控製
조성여진동공제
NOISE AND VIBRATION CONTROL
2014年
6期
210-214
,共5页
李辉%马卫东%孙志勇%孙国华%李斌%杜华太
李輝%馬衛東%孫誌勇%孫國華%李斌%杜華太
리휘%마위동%손지용%손국화%리빈%두화태
振动与波%自粘性%阻尼橡胶%共振频率%弹性剪切模量%剪切损耗因子
振動與波%自粘性%阻尼橡膠%共振頻率%彈性剪切模量%剪切損耗因子
진동여파%자점성%조니상효%공진빈솔%탄성전절모량%전절손모인자
vibration and wave%self-adhered%damping rubber%resonant frequency%shear modulus%shear lose facture
根据标准ASTM E756-05(2010),对阻尼橡胶材料阻尼性能悬臂梁共振法的测试方法进行了研究,分析接触式响应传感器引入的附加质量及激励传感器和响应传感器的安装位置对测试结果的影响,并得到有意义的结论。试验结果表明:质量为0.6 g的接触式响应传感器引入的附加质量对材料的弹性剪切模量和剪切损耗因子的影响较小,测试结果满足标准ASTM E756-05(2010)对测试精度的规定;选择合适的激励器安装位置有利于提高传递函数曲线幅值;响应传感器的安装位置对传递函数曲线影响较大,测试时应根据所要获得的模态信息选择合适的测点。
根據標準ASTM E756-05(2010),對阻尼橡膠材料阻尼性能懸臂樑共振法的測試方法進行瞭研究,分析接觸式響應傳感器引入的附加質量及激勵傳感器和響應傳感器的安裝位置對測試結果的影響,併得到有意義的結論。試驗結果錶明:質量為0.6 g的接觸式響應傳感器引入的附加質量對材料的彈性剪切模量和剪切損耗因子的影響較小,測試結果滿足標準ASTM E756-05(2010)對測試精度的規定;選擇閤適的激勵器安裝位置有利于提高傳遞函數麯線幅值;響應傳感器的安裝位置對傳遞函數麯線影響較大,測試時應根據所要穫得的模態信息選擇閤適的測點。
근거표준ASTM E756-05(2010),대조니상효재료조니성능현비량공진법적측시방법진행료연구,분석접촉식향응전감기인입적부가질량급격려전감기화향응전감기적안장위치대측시결과적영향,병득도유의의적결론。시험결과표명:질량위0.6 g적접촉식향응전감기인입적부가질량대재료적탄성전절모량화전절손모인자적영향교소,측시결과만족표준ASTM E756-05(2010)대측시정도적규정;선택합괄적격려기안장위치유리우제고전체함수곡선폭치;향응전감기적안장위치대전체함수곡선영향교대,측시시응근거소요획득적모태신식선택합괄적측점。
The vibration damping properties of damping rubber materials were tested according to ASTM E756-05 (2010) based on the cantilever resonance method. The effects of the additional weight induced by the contacting response transducer and the arrangements of the exciter transducer and response transducer were analyzed. The results show that the additional weight of the contacting response transducer with 0.6 g mass has little contribution to the shear loss factor and the shear modulus. The suitable arrangement of the exciter transducer can cause the increase of the FRF amplitude, and the arrangement of the response transducer has a large effect on transmission function curve. So, locations of the response transducers should be chosen reasonably according to the required modal signals.