粉末冶金工业
粉末冶金工業
분말야금공업
POWDER METALLURGY INDUSTRY
2014年
6期
11-15
,共5页
徐坚%王文焱%张豪胤%谢敬佩%李洛利
徐堅%王文焱%張豪胤%謝敬珮%李洛利
서견%왕문염%장호윤%사경패%리락리
Ti-6Al-4V%粉末冶金%微合金化%微观组织%力学性能
Ti-6Al-4V%粉末冶金%微閤金化%微觀組織%力學性能
Ti-6Al-4V%분말야금%미합금화%미관조직%역학성능
Ti-6Al-4V%powder metallurgy%microalloying%microstructure%mechanical property
采用冷等静压、真空烧结的方法制备不同Cr含量的Ti-6Al-4V合金,通过金相观察、力学性能测试及SEM分析等方法研究Cr元素对Ti-6Al-4V合金显微组织与力学性能的影响.结果表明:添加Cr元素后,合金中并未出现化合物TiCr2,其组织是由(α+β)相组成的魏氏组织.Cr的添加降低了合金的致密度,提高了其抗压强度,当Cr质量分数为4%时,合金的抗压强度达到1 855 MPa.Cr质量分数为1%、2%时,合金断裂形式为韧性断裂;Cr含量为3%、4%时,合金断裂形式为解理断裂.
採用冷等靜壓、真空燒結的方法製備不同Cr含量的Ti-6Al-4V閤金,通過金相觀察、力學性能測試及SEM分析等方法研究Cr元素對Ti-6Al-4V閤金顯微組織與力學性能的影響.結果錶明:添加Cr元素後,閤金中併未齣現化閤物TiCr2,其組織是由(α+β)相組成的魏氏組織.Cr的添加降低瞭閤金的緻密度,提高瞭其抗壓彊度,噹Cr質量分數為4%時,閤金的抗壓彊度達到1 855 MPa.Cr質量分數為1%、2%時,閤金斷裂形式為韌性斷裂;Cr含量為3%、4%時,閤金斷裂形式為解理斷裂.
채용랭등정압、진공소결적방법제비불동Cr함량적Ti-6Al-4V합금,통과금상관찰、역학성능측시급SEM분석등방법연구Cr원소대Ti-6Al-4V합금현미조직여역학성능적영향.결과표명:첨가Cr원소후,합금중병미출현화합물TiCr2,기조직시유(α+β)상조성적위씨조직.Cr적첨가강저료합금적치밀도,제고료기항압강도,당Cr질량분수위4%시,합금적항압강도체도1 855 MPa.Cr질량분수위1%、2%시,합금단렬형식위인성단렬;Cr함량위3%、4%시,합금단렬형식위해리단렬.