工业加热
工業加熱
공업가열
INDUSTRIIAL HEATING
2014年
6期
16-19
,共4页
于哲%李言栋%刘承军%姜茂发
于哲%李言棟%劉承軍%薑茂髮
우철%리언동%류승군%강무발
稀土钢%耐热钢%凝固%夹杂物%偏析%FactSage
稀土鋼%耐熱鋼%凝固%夾雜物%偏析%FactSage
희토강%내열강%응고%협잡물%편석%FactSage
rare earth steel%heat resistant steel%solidification%inclusions%segregation%FactSage
基于FactSage热力学软件的最小吉布斯自由能原理,系统研究了不同铈含量及钢液洁净度条件下耐热钢凝固过程中夹杂物的析出行为。结果表明:耐热钢中添加铈后,高熔点的Ce2O2S、 Ce2O3等夹杂取代了SiO2与MnS夹杂;在一定洁净度条件下, SiO2与MnS无法析出的铈含量分别为0.02%与0.03%;随着氧含量的增加,耐热钢中的夹杂物类型由Ce2O2S、 CeN、 CeS向SiO2、 Ce2O3转变,当氧含量大于0.006%时,钢中开始析出SiO2夹杂;随着硫含量的增加,耐热钢中的夹杂物类型由Ce2O2S、 CeN、 CeS、 Ce2O3向Ce2O2S、 MnS、 Ce2S3转变,当硫含量大于0.005%时, MnS夹杂开始析出。
基于FactSage熱力學軟件的最小吉佈斯自由能原理,繫統研究瞭不同鈰含量及鋼液潔淨度條件下耐熱鋼凝固過程中夾雜物的析齣行為。結果錶明:耐熱鋼中添加鈰後,高鎔點的Ce2O2S、 Ce2O3等夾雜取代瞭SiO2與MnS夾雜;在一定潔淨度條件下, SiO2與MnS無法析齣的鈰含量分彆為0.02%與0.03%;隨著氧含量的增加,耐熱鋼中的夾雜物類型由Ce2O2S、 CeN、 CeS嚮SiO2、 Ce2O3轉變,噹氧含量大于0.006%時,鋼中開始析齣SiO2夾雜;隨著硫含量的增加,耐熱鋼中的夾雜物類型由Ce2O2S、 CeN、 CeS、 Ce2O3嚮Ce2O2S、 MnS、 Ce2S3轉變,噹硫含量大于0.005%時, MnS夾雜開始析齣。
기우FactSage열역학연건적최소길포사자유능원리,계통연구료불동시함량급강액길정도조건하내열강응고과정중협잡물적석출행위。결과표명:내열강중첨가시후,고용점적Ce2O2S、 Ce2O3등협잡취대료SiO2여MnS협잡;재일정길정도조건하, SiO2여MnS무법석출적시함량분별위0.02%여0.03%;수착양함량적증가,내열강중적협잡물류형유Ce2O2S、 CeN、 CeS향SiO2、 Ce2O3전변,당양함량대우0.006%시,강중개시석출SiO2협잡;수착류함량적증가,내열강중적협잡물류형유Ce2O2S、 CeN、 CeS、 Ce2O3향Ce2O2S、 MnS、 Ce2S3전변,당류함량대우0.005%시, MnS협잡개시석출。
Based on Gibbs free energy minimization principle, the thermodynamic software FactSage was chosen to calculate and analyze the precipitation behavior of inclusions in heat resistant steel with different cerium content and cleanliness. The results show that, SiO2 and MnS inclusions are replaced by Ce2O3, Ce2O2S when cerium is added to heat resistant steel. Under the conditions of certain cleanliness of molten steel, the content of cerium when SiO2 and MnS cannot precipitate are 0.02%and 0.03%respectively; the inclusions precipitated in heat resistant steel transform from Ce2O2S, CeN, CeS to SiO2, Ce2O3 with the content of oxygen increasing. SiO2 can precipitate in steel when the content of oxygen is greater than 0.006%. The inclusions precipitated in the heat resistant steel transform from Ce 2O2S, CeN, CeS, Ce2O3 to Ce2O2S, MnS, Ce2S3 with the content of sulfur increasing. MnS can precipitate in steel when the content of sulfur is greater than 0.005%.