热力发电
熱力髮電
열력발전
THERMAL POWER GENERATION
2014年
12期
95-98,135
,共5页
锅炉%褐煤%风扇磨煤机%选型%通风量%提升压力
鍋爐%褐煤%風扇磨煤機%選型%通風量%提升壓力
과로%갈매%풍선마매궤%선형%통풍량%제승압력
boiler%lignite%fan mill%type-selection%ventilation volume%boost pressure
依托S02型磨煤机,对胜利5层褐煤开展试验研究及选型计算,提出了采用与胜利5层褐煤相匹配FM410.1300型风扇磨煤机,并按6+2进行配置,在单台磨煤机通风量满足 BMCR负荷对给煤量干燥的要求时,风煤比为1.54.按照 S02型磨煤机试验曲线得出的煤粉细度R90、制粉单耗、磨煤机通风量和提升压力,并对其修正后得到该风扇磨煤机的提升压力为1594 Pa.制粉系统管道阻力建议与该磨煤机提升压力相匹配.对小型 S02型磨煤机和现场MB3600/1000/490型大型风扇磨煤机分别进行了胜利5层褐煤风扇磨煤机的选型计算,得出的磨煤机提升压力计算结果基本一致,表明依据小型S02型风扇磨煤机进行风扇磨煤机关键参数选型可行.
依託S02型磨煤機,對勝利5層褐煤開展試驗研究及選型計算,提齣瞭採用與勝利5層褐煤相匹配FM410.1300型風扇磨煤機,併按6+2進行配置,在單檯磨煤機通風量滿足 BMCR負荷對給煤量榦燥的要求時,風煤比為1.54.按照 S02型磨煤機試驗麯線得齣的煤粉細度R90、製粉單耗、磨煤機通風量和提升壓力,併對其脩正後得到該風扇磨煤機的提升壓力為1594 Pa.製粉繫統管道阻力建議與該磨煤機提升壓力相匹配.對小型 S02型磨煤機和現場MB3600/1000/490型大型風扇磨煤機分彆進行瞭勝利5層褐煤風扇磨煤機的選型計算,得齣的磨煤機提升壓力計算結果基本一緻,錶明依據小型S02型風扇磨煤機進行風扇磨煤機關鍵參數選型可行.
의탁S02형마매궤,대성리5층갈매개전시험연구급선형계산,제출료채용여성리5층갈매상필배FM410.1300형풍선마매궤,병안6+2진행배치,재단태마매궤통풍량만족 BMCR부하대급매량간조적요구시,풍매비위1.54.안조 S02형마매궤시험곡선득출적매분세도R90、제분단모、마매궤통풍량화제승압력,병대기수정후득도해풍선마매궤적제승압력위1594 Pa.제분계통관도조력건의여해마매궤제승압력상필배.대소형 S02형마매궤화현장MB3600/1000/490형대형풍선마매궤분별진행료성리5층갈매풍선마매궤적선형계산,득출적마매궤제승압력계산결과기본일치,표명의거소형S02형풍선마매궤진행풍선마매궤관건삼수선형가행.
On the basis of the test research on Shengli lignite coal grinding and calculation about large fan mill type-selection,the method of fan mill type-selection was proposed for lignite with low calorific value, low grindability,high moisture and used in high altitude conditions.It suggested the FM410.1300 fan mill be adopted and configured in 6+2 mode.When the ventilation volume of a single fan mill satisfies the re-quirements of coal dryness in BMCR load condition,the air coal ratio is 1.54.Furthermore,according to such parameters as coal fineness R90,pulverizing unit coal consumption,ventilation and booster pressure picked up in the commissioning curves of S02 mill,the corrected booster pressure of the FM410.1 300 fan mill is 1 594 Pa.The pipeline resistance is suggested to be matched with the corresponding booster pres-sure.Fan mill type selection calculation for small S02 mill and the field MB3600/1000/490 large scale fan mill was conducted respectively.The obtained booster pressure agrees well with each other,indicating u-sing the S02 fan mill to select the key parameters is reliable.