铸造
鑄造
주조
FOUNDRY
2015年
2期
110-112
,共3页
游龙%焦景华%邢志辉%杨慧慧
遊龍%焦景華%邢誌輝%楊慧慧
유룡%초경화%형지휘%양혜혜
锡青铜%析出强化%硬度%时效处理
錫青銅%析齣彊化%硬度%時效處理
석청동%석출강화%경도%시효처리
tin bronze%precipitation strengthened%hardness%aging treatment
采用真空离心铸造方法制备了析出强化ZCuSn 10Zn2FeCo合金试样,经780℃下保温4h后水淬固溶处理,随后在时效处理温度300℃、400℃、500℃、600℃下各保温4h,利用扫描电子显微镜(SEM)分析了铸态、固溶态以及时效处理后合金中析出富含铁、钴粒子的分布规律,并测量了各状态下的硬度.结果表明:合金中析出富含Fe、Co的富集相粒子,固溶处理后合金的硬度最低,随着时效处理温度的升高,析出相数目增多,分布更为弥散均匀,硬度先升高后降低,400℃时达到最大值HB134.4,与铸态ZCuSn10Zn2FeCo合金的硬度值HB103.6相比提高了29.7%,之后硬度急剧下降,发生了过时效.
採用真空離心鑄造方法製備瞭析齣彊化ZCuSn 10Zn2FeCo閤金試樣,經780℃下保溫4h後水淬固溶處理,隨後在時效處理溫度300℃、400℃、500℃、600℃下各保溫4h,利用掃描電子顯微鏡(SEM)分析瞭鑄態、固溶態以及時效處理後閤金中析齣富含鐵、鈷粒子的分佈規律,併測量瞭各狀態下的硬度.結果錶明:閤金中析齣富含Fe、Co的富集相粒子,固溶處理後閤金的硬度最低,隨著時效處理溫度的升高,析齣相數目增多,分佈更為瀰散均勻,硬度先升高後降低,400℃時達到最大值HB134.4,與鑄態ZCuSn10Zn2FeCo閤金的硬度值HB103.6相比提高瞭29.7%,之後硬度急劇下降,髮生瞭過時效.
채용진공리심주조방법제비료석출강화ZCuSn 10Zn2FeCo합금시양,경780℃하보온4h후수쉬고용처리,수후재시효처리온도300℃、400℃、500℃、600℃하각보온4h,이용소묘전자현미경(SEM)분석료주태、고용태이급시효처리후합금중석출부함철、고입자적분포규률,병측량료각상태하적경도.결과표명:합금중석출부함Fe、Co적부집상입자,고용처리후합금적경도최저,수착시효처리온도적승고,석출상수목증다,분포경위미산균균,경도선승고후강저,400℃시체도최대치HB134.4,여주태ZCuSn10Zn2FeCo합금적경도치HB103.6상비제고료29.7%,지후경도급극하강,발생료과시효.