电焊机
電銲機
전한궤
ELECTRIC WELDING MACHINE
2014年
12期
79-85,89
,共8页
锥柱耐压壳%两条焊缝%焊接接头%残余应力%数值模拟
錐柱耐壓殼%兩條銲縫%銲接接頭%殘餘應力%數值模擬
추주내압각%량조한봉%한접접두%잔여응력%수치모의
cone-cylinder pressure hull%two welds%welded joint%residual stress%numerical simulation
基于热-弹塑性相关理论,采用ANSYS的APDL语言编制焊接残余应力数值模拟程序,采用生死单元技术及间接耦合法模拟了典型焊接接头只焊一条焊缝、两条焊缝同时焊和两条焊缝分开焊三种模拟方法的轴向焊接残余应力σx.结果表明:采用不同模拟方法,典型焊接接头的变化规律一致,均在焊缝附近达到最大值;但采用不同方法得到的σx应力水平不同,两条焊缝的残余应力会相互影响,在进行相关研究时这种影响需要考虑在内.两条焊缝分开焊与同时焊相比,分开焊可以在一定程度上减小焊缝中心附近区域的轴向焊接残余应力,且在焊缝的凸面这种减小作用更加明显.
基于熱-彈塑性相關理論,採用ANSYS的APDL語言編製銲接殘餘應力數值模擬程序,採用生死單元技術及間接耦閤法模擬瞭典型銲接接頭隻銲一條銲縫、兩條銲縫同時銲和兩條銲縫分開銲三種模擬方法的軸嚮銲接殘餘應力σx.結果錶明:採用不同模擬方法,典型銲接接頭的變化規律一緻,均在銲縫附近達到最大值;但採用不同方法得到的σx應力水平不同,兩條銲縫的殘餘應力會相互影響,在進行相關研究時這種影響需要攷慮在內.兩條銲縫分開銲與同時銲相比,分開銲可以在一定程度上減小銲縫中心附近區域的軸嚮銲接殘餘應力,且在銲縫的凸麵這種減小作用更加明顯.
기우열-탄소성상관이론,채용ANSYS적APDL어언편제한접잔여응력수치모의정서,채용생사단원기술급간접우합법모의료전형한접접두지한일조한봉、량조한봉동시한화량조한봉분개한삼충모의방법적축향한접잔여응력σx.결과표명:채용불동모의방법,전형한접접두적변화규률일치,균재한봉부근체도최대치;단채용불동방법득도적σx응력수평불동,량조한봉적잔여응력회상호영향,재진행상관연구시저충영향수요고필재내.량조한봉분개한여동시한상비,분개한가이재일정정도상감소한봉중심부근구역적축향한접잔여응력,차재한봉적철면저충감소작용경가명현.