光学精密工程
光學精密工程
광학정밀공정
OPTICS AND PRECISION ENGINEERING
2015年
4期
1004-1010
,共7页
王辉%武俊峰%李胤%吴一辉
王輝%武俊峰%李胤%吳一輝
왕휘%무준봉%리윤%오일휘
反作用飞轮%印刷电路板定子绕组%轴向磁通永磁电机%有限元
反作用飛輪%印刷電路闆定子繞組%軸嚮磁通永磁電機%有限元
반작용비륜%인쇄전로판정자요조%축향자통영자전궤%유한원
reaction flywheel%Printed Circuit Board (PCB) stator winding%axial flux permanent magnet motor%Finite Element Analysis (FEA)
针对卫星姿态控制用反作用飞轮小型化的要求,设计了采用印刷电路板(PCB)定子绕组形式的轴向磁通反作用飞轮系统,并研究了PCB定子绕组的布线形式.根据系统设计方案和工艺的要求,采用理论分析与有限元仿真相结合的方法,研究了螺旋形绕组的反向转矩产生机理,对比分析了螺旋形和波形PCB定子绕组对飞轮驱动电机性能的影响,并分别对采用两种形式定子绕组的飞轮样机进行了地面性能测试.试验结果表明,飞轮工作在额定转速5 000 r/min时,采用波形定子绕组比采用螺旋形定子绕组时的电机功耗降低了26.2%,电磁效率降低了0.8%.试验结果验证了理论分析与仿真结果的正确性,为PCB定子绕组型轴向磁通永磁电机的工程化应用提供了参考.
針對衛星姿態控製用反作用飛輪小型化的要求,設計瞭採用印刷電路闆(PCB)定子繞組形式的軸嚮磁通反作用飛輪繫統,併研究瞭PCB定子繞組的佈線形式.根據繫統設計方案和工藝的要求,採用理論分析與有限元倣真相結閤的方法,研究瞭螺鏇形繞組的反嚮轉矩產生機理,對比分析瞭螺鏇形和波形PCB定子繞組對飛輪驅動電機性能的影響,併分彆對採用兩種形式定子繞組的飛輪樣機進行瞭地麵性能測試.試驗結果錶明,飛輪工作在額定轉速5 000 r/min時,採用波形定子繞組比採用螺鏇形定子繞組時的電機功耗降低瞭26.2%,電磁效率降低瞭0.8%.試驗結果驗證瞭理論分析與倣真結果的正確性,為PCB定子繞組型軸嚮磁通永磁電機的工程化應用提供瞭參攷.
침대위성자태공제용반작용비륜소형화적요구,설계료채용인쇄전로판(PCB)정자요조형식적축향자통반작용비륜계통,병연구료PCB정자요조적포선형식.근거계통설계방안화공예적요구,채용이론분석여유한원방진상결합적방법,연구료라선형요조적반향전구산생궤리,대비분석료라선형화파형PCB정자요조대비륜구동전궤성능적영향,병분별대채용량충형식정자요조적비륜양궤진행료지면성능측시.시험결과표명,비륜공작재액정전속5 000 r/min시,채용파형정자요조비채용라선형정자요조시적전궤공모강저료26.2%,전자효솔강저료0.8%.시험결과험증료이론분석여방진결과적정학성,위PCB정자요조형축향자통영자전궤적공정화응용제공료삼고.