塑料工业
塑料工業
소료공업
CHINA PLASTICS INDUSTRY
2015年
4期
5-9
,共5页
王鉴%李杨%祝宝东%张建伟%孟庆明
王鑒%李楊%祝寶東%張建偉%孟慶明
왕감%리양%축보동%장건위%맹경명
聚丙烯%熔融接枝%甲基丙烯酸丁酯%马来酸酐%水接触角
聚丙烯%鎔融接枝%甲基丙烯痠丁酯%馬來痠酐%水接觸角
취병희%용융접지%갑기병희산정지%마래산항%수접촉각
Polypropylene%Melt Extrusion%Butyl Methacrylate%Maleic Anhydride%Water Contact Angle
以甲基丙烯酸丁酯(BMA)为共单体,采用熔融挤出法制备了马来酸酐(MAH)接枝聚丙烯(PP)共聚物PP-g-(MAH-BMA).通过比较水接触角研究了单体配比和用量、引发剂用量及螺杆转速等因素对接枝效果的影响,并与以苯乙烯(St)为共单体和第三单体的接枝PP产物进行了比较.结果表明,以BMA为共单体提高了接枝产物的接枝率,同时能有效抑制PP分子断链降解,产品的凝胶率为零.随着单体用量、引发剂用量和螺杆转速的增加,改性产品的水接触角均出现极小值.当BMA与MAH的物质的量比为1∶1、MAH的含量为PP质量的3%、引发剂DCP含量为PP质量的0.05%、螺杆转速为160 r/min时,接枝共聚物PP-g-(MAH-BMA)水接触角最低为72°,产物极性显著提高.添加苯乙烯形成的三单体接枝物的黏均摩尔质量和熔体质量流动速率与PP-g-(MAH-BMA)相差不多,但其水接触角却有所增加,并生成凝胶.
以甲基丙烯痠丁酯(BMA)為共單體,採用鎔融擠齣法製備瞭馬來痠酐(MAH)接枝聚丙烯(PP)共聚物PP-g-(MAH-BMA).通過比較水接觸角研究瞭單體配比和用量、引髮劑用量及螺桿轉速等因素對接枝效果的影響,併與以苯乙烯(St)為共單體和第三單體的接枝PP產物進行瞭比較.結果錶明,以BMA為共單體提高瞭接枝產物的接枝率,同時能有效抑製PP分子斷鏈降解,產品的凝膠率為零.隨著單體用量、引髮劑用量和螺桿轉速的增加,改性產品的水接觸角均齣現極小值.噹BMA與MAH的物質的量比為1∶1、MAH的含量為PP質量的3%、引髮劑DCP含量為PP質量的0.05%、螺桿轉速為160 r/min時,接枝共聚物PP-g-(MAH-BMA)水接觸角最低為72°,產物極性顯著提高.添加苯乙烯形成的三單體接枝物的黏均摩爾質量和鎔體質量流動速率與PP-g-(MAH-BMA)相差不多,但其水接觸角卻有所增加,併生成凝膠.
이갑기병희산정지(BMA)위공단체,채용용융제출법제비료마래산항(MAH)접지취병희(PP)공취물PP-g-(MAH-BMA).통과비교수접촉각연구료단체배비화용량、인발제용량급라간전속등인소대접지효과적영향,병여이분을희(St)위공단체화제삼단체적접지PP산물진행료비교.결과표명,이BMA위공단체제고료접지산물적접지솔,동시능유효억제PP분자단련강해,산품적응효솔위령.수착단체용량、인발제용량화라간전속적증가,개성산품적수접촉각균출현겁소치.당BMA여MAH적물질적량비위1∶1、MAH적함량위PP질량적3%、인발제DCP함량위PP질량적0.05%、라간전속위160 r/min시,접지공취물PP-g-(MAH-BMA)수접촉각최저위72°,산물겁성현저제고.첨가분을희형성적삼단체접지물적점균마이질량화용체질량류동속솔여PP-g-(MAH-BMA)상차불다,단기수접촉각각유소증가,병생성응효.