机械设计与制造
機械設計與製造
궤계설계여제조
MACHINERY DESIGN & MANUFACTURE
2015年
5期
29-31,35
,共4页
TBM%离散元%出碴槽%PFC3D%开口面积
TBM%離散元%齣碴槽%PFC3D%開口麵積
TBM%리산원%출사조%PFC3D%개구면적
TBM%DEM%Mucking Slot%PFC%Open Area
研究了全断面岩石掘进机(TBM)的最小开口面积.以5.55m直径刀盘为研究对象,建立了不同开口面积刀盘的三维面体模型,基于离散元仿真软件PFC3D对TBM刀盘的出碴过程进行仿真,得到刀盘的合理开口面积.结果表明,随着刀盘开口面积的增大,刀盘内部的颗粒数量达到稳定状态就越快,且波动也越小;当刀盘开口面积大于2.5m2时,随着开口面积的增大刀盘内部颗粒数量的方差减小的就越缓慢;在开口面积约为2.7m2时,单位时间内的排碴量与破岩量相等.以单位时间内排碴量大于破岩量且刀盘内部颗粒数量波动尽量小为原则,得到5.55m直径刀盘的合理开口面积为(2.7~3.5)m2.
研究瞭全斷麵巖石掘進機(TBM)的最小開口麵積.以5.55m直徑刀盤為研究對象,建立瞭不同開口麵積刀盤的三維麵體模型,基于離散元倣真軟件PFC3D對TBM刀盤的齣碴過程進行倣真,得到刀盤的閤理開口麵積.結果錶明,隨著刀盤開口麵積的增大,刀盤內部的顆粒數量達到穩定狀態就越快,且波動也越小;噹刀盤開口麵積大于2.5m2時,隨著開口麵積的增大刀盤內部顆粒數量的方差減小的就越緩慢;在開口麵積約為2.7m2時,單位時間內的排碴量與破巖量相等.以單位時間內排碴量大于破巖量且刀盤內部顆粒數量波動儘量小為原則,得到5.55m直徑刀盤的閤理開口麵積為(2.7~3.5)m2.
연구료전단면암석굴진궤(TBM)적최소개구면적.이5.55m직경도반위연구대상,건립료불동개구면적도반적삼유면체모형,기우리산원방진연건PFC3D대TBM도반적출사과정진행방진,득도도반적합리개구면적.결과표명,수착도반개구면적적증대,도반내부적과립수량체도은정상태취월쾌,차파동야월소;당도반개구면적대우2.5m2시,수착개구면적적증대도반내부과립수량적방차감소적취월완만;재개구면적약위2.7m2시,단위시간내적배사량여파암량상등.이단위시간내배사량대우파암량차도반내부과립수량파동진량소위원칙,득도5.55m직경도반적합리개구면적위(2.7~3.5)m2.