CAJ | 학술논문

为了通过理论的方法准确预测液力透平的性能，该文分析了叶轮内部相对环流流动的特征，提出了3种计算离心泵反转作液力透平叶轮出口滑移系数的方法，得到了相应的叶轮出口滑移系数解析计算公式，然后采用10组离心泵反转作液力透平的试验数据对所提出的滑移系数计算公式进行验证，最后得出与试验结果较为吻合的解析公式。结果表明：当假设叶片工作面上的相对涡诱导速度与叶轮出口边上的相对涡诱导速度的比值等于叶片和涡心所张曲边三角形的面积与叶轮出口边和涡心所张曲边三角形的面积之比时，得到的液力透平叶轮出口滑移系数的计算公式最准确，可用于较准确地预测液力透平的性能。在计算液力透平叶轮内的滑移时只需计算叶轮出口的滑移。该研究结果为更加精确地通过理论方法预测液力透平的性能提供了参考。
위료통과이론적방법준학예측액력투평적성능，해문분석료협륜내부상대배류류동적특정，제출료3충계산리심빙반전작액력투평협륜출구활이계수적방법，득도료상응적협륜출구활이계수해석계산공식，연후채용10조리심빙반전작액력투평적시험수거대소제출적활이계수계산공식진행험증，최후득출여시험결과교위문합적해석공식。결과표명：당가설협편공작면상적상대와유도속도여협륜출구변상적상대와유도속도적비치등우협편화와심소장곡변삼각형적면적여협륜출구변화와심소장곡변삼각형적면적지비시，득도적액력투평협륜출구활이계수적계산공식최준학，가용우교준학지예측액력투평적성능。재계산액력투평협륜내적활이시지수계산협륜출구적활이。해연구결과위경가정학지통과이론방법예측액력투평적성능제공료삼고。
A centrifugal pump can be operated in its reverse rotational direction as a turbine-a prime motor, and its impeller is a kind of centripetal impeller. It can convert the high pressure energy of a fluid into the rotational mechanical energy of the rotor to drive a generator to generate electricity or drive a working machine, realizing an energy recycling of the high pressure fluid. It is well-known that the slip phenomenon exists in turbomachinery, such as hydraulic turbine, steam turbine, roto-dynamic pumps and compressors. This is also true for a centrifugal pump as turbine. The slip velocity may be smaller in a hydraulic turbine than a centrifugal pump. However, this is not the case for a centrifugal pump as turbine because its number of blades is much less compared with the hydraulic turbine. The constraint ability of blade is less for fluid giving rise a smaller slip factor. In addition, a slip factor is the key parameter to estimate the turbine output power based on its existing geometry and designed flow condition to check if its output power has met the requirement by end-users. Unfortunately, this topic is not well documented currently. In this paper, we put forward an analytical method to accurately determine the slip factor at the impeller outlet in a centrifugal pump as turbine in order to predict the turbine performance correctly. Firstly, the relative eddy flow in an impeller passage with closed inlet and outlet was analyzed for a centrifugal pump in its turbine mode. Secondly, three assumptions were made for the induced velocity by the eddy on the blade pressure side, then the slip velocities and the corresponding slip factors at the impeller outlet under these assumptions were derived analytically. Finally, the slip factor formulas were validated by means of the theoretical heads of ten centrifugal pumps as turbines based on their experimental data. Two cases, namely, the slip factors at both impeller inlet and outlet, and the slip factor at the impeller outlet alone, were studied, respectively. It was identified that the slip factor formula based on the second assumption, in which the ratio of the induced velocity on the blade pressure side over the slip velocity on the impeller outlet was equal to the ratio of the areas of two triangles with the pressure side and impeller outlet as one curved edge respectively, was subject to a very good accuracy. Moreover, it was unnecessary to include the slip factor at the impeller inlet when predicting the theoretical head of a pump as turbine. The influence factors of the slip on the centripetal impeller outlet of hydraulic turbine have the entrance and outlet diameter of impeller, entrance and outlet blade angle of blade and the number of blades. The research results improved the accuracy for predicting the performance of hydraulic turbine by the theoretical method, and this kind of method will be convenient and efficient when scholars predict the performance of hydraulic turbine, and may save the cost of research. The results provide a base for more accurately predicting the performance of a pump as turbine by making use of analytical methods.