振动与冲击
振動與遲擊
진동여충격
JOURNAL OF VIBRATION AND SHOCK
2015年
12期
157-163
,共7页
邓开来%潘鹏%苏宇坤%孙江波%钱稼茹
鄧開來%潘鵬%囌宇坤%孫江波%錢稼茹
산개래%반붕%소우곤%손강파%전가여
开槽 U 型阻尼器%面外性能%拟静力试验%虚功原理
開槽 U 型阻尼器%麵外性能%擬靜力試驗%虛功原理
개조 U 형조니기%면외성능%의정력시험%허공원리
slotted U-shaped steel damper%out-of-plane behavior%quasi-static test%principle of virtual work
在隔震层安装金属屈服阻尼器可以有效控制隔震层在地震下的位移。由于隔震层在地震下产生多向变形,因此要求安装在隔震层中的金属屈服阻尼器需具有多向的变形能力。既往研究表明 U 型金属屈服阻尼器在面内具有良好的耗能能力,对于提高结构阻尼比,控制隔震结构的位移具有非常显著的作用。然而关于其面外性能的深入研究尚未见报道。提出了开槽 U 型阻尼器以提高其面外性能,并通过拟静力试验考察了阻尼器宽度,高度,以及长度对其面外性能的影响,实验表明合理设计的开槽 U 型阻尼器具有良好的耗能能力和低周疲劳性能。同时采用有限元方法补充了试件的数量,进行了参数分析。根据参数分析的结果提出了开槽型 U 型金属屈服阻尼器的屈服位移,屈服恢复力设计公式。另一方面,根据虚功原理提出了开槽 U 型阻尼器的极限恢复力计算公式,并通过试验结果与有限元模型的计算结果校对了该公式的精度和适用范围。
在隔震層安裝金屬屈服阻尼器可以有效控製隔震層在地震下的位移。由于隔震層在地震下產生多嚮變形,因此要求安裝在隔震層中的金屬屈服阻尼器需具有多嚮的變形能力。既往研究錶明 U 型金屬屈服阻尼器在麵內具有良好的耗能能力,對于提高結構阻尼比,控製隔震結構的位移具有非常顯著的作用。然而關于其麵外性能的深入研究尚未見報道。提齣瞭開槽 U 型阻尼器以提高其麵外性能,併通過擬靜力試驗攷察瞭阻尼器寬度,高度,以及長度對其麵外性能的影響,實驗錶明閤理設計的開槽 U 型阻尼器具有良好的耗能能力和低週疲勞性能。同時採用有限元方法補充瞭試件的數量,進行瞭參數分析。根據參數分析的結果提齣瞭開槽型 U 型金屬屈服阻尼器的屈服位移,屈服恢複力設計公式。另一方麵,根據虛功原理提齣瞭開槽 U 型阻尼器的極限恢複力計算公式,併通過試驗結果與有限元模型的計算結果校對瞭該公式的精度和適用範圍。
재격진층안장금속굴복조니기가이유효공제격진층재지진하적위이。유우격진층재지진하산생다향변형,인차요구안장재격진층중적금속굴복조니기수구유다향적변형능력。기왕연구표명 U 형금속굴복조니기재면내구유량호적모능능력,대우제고결구조니비,공제격진결구적위이구유비상현저적작용。연이관우기면외성능적심입연구상미견보도。제출료개조 U 형조니기이제고기면외성능,병통과의정력시험고찰료조니기관도,고도,이급장도대기면외성능적영향,실험표명합리설계적개조 U 형조니기구유량호적모능능력화저주피로성능。동시채용유한원방법보충료시건적수량,진행료삼수분석。근거삼수분석적결과제출료개조형 U 형금속굴복조니기적굴복위이,굴복회복력설계공식。령일방면,근거허공원리제출료개조 U 형조니기적겁한회복력계산공식,병통과시험결과여유한원모형적계산결과교대료해공식적정도화괄용범위。
Metal dampers installed in base isolation layers are effective to control the displacement of the base isolation layers under earthquakes.The base-isolation layers deform in multiple directions during an earthquake,requiring that the dampers should also have multi-directional deformation capacity.Previous studies suggest the U-shaped steel dampers which have satisfactory deformation and energy dissipation capacity in-plane,and can significantly increase the damping of the structures and control the displacement of the base isolation layers.However,the out-of-plane behaviours of the U-shaped steel dampers are not necessarily satisfactory.To this end,a new type of slotted U-shaped steel damper was proposed to improve the out-of-plane performances of the U-shaped steel damper.The effects of the damper width, height,and length on the damper performances were investigated by using quasi-static tests.The test results indicate that the U-shaped steel damper with appropriate design parameters has satisfactory energy dissipation capacity and low cycle fatigue behaviour.The formulation is accurate for the estimation of damper strength.Parametric finite element analysis was conducted to supplement the test results.Based on the results of parametric analysis,the formulas for yield displacement and restoring force of the slotted U-shaped damper were derived by using regression analysis.The formula to estimate the dampers ultimate restoring forces was also derived based on the virtual work principle.The accuracies and application conditions of the formulas proposed were investigated according to the results of experiment and numerical analysis.