纺织学报
紡織學報
방직학보
JOURNAL OF TEXTILE RESEARCH
2015年
6期
13-17
,共5页
唐兵兵%李健%郭增革%甘丽华%李鑫
唐兵兵%李健%郭增革%甘麗華%李鑫
당병병%리건%곽증혁%감려화%리흠
聚酯%压力系数%特性黏度%流变行为
聚酯%壓力繫數%特性黏度%流變行為
취지%압력계수%특성점도%류변행위
PET%pressure coefficient%intrinsic viscosity%rheological behavior
采用毛细管流变仪及其配套的反向压力腔组件控制毛细管出口压力,在平均压力为5 ~50 MPa下研究了3种不同特性黏度的聚酯(PET)的流变行为.结果表明:PET的剪切黏度随着平均压力的增大都呈指数增加,符合Barus方程.压力系数随着特性黏度的增大而减小,当特性黏度由0.48增加至0.67 dL/g时,压力系数显著减小,且这种变化随着剪切速率的增大而衰减,当特性黏度≥0.67 dL/g时,压力系数随剪切速率的变化不大.压力系数随剪切速率的增大而减小,特性黏度为0.48 dL/g时变化显著,当特性黏度≥0.67 dL/g时,压力系数随剪切速率的变化不大.压力系数随着温度的升高而减小,且变化率随着温度的升高显著减小.不同特性黏度PET压力系数的变化表明,特性黏度较低时,自由体积较大,表现在玻璃化转变温度低,受压力的影响显著;当特性黏度为0.67和1.00 dL/g时,自由体积的减小不再明显,因此受压力的影响也不再明显.
採用毛細管流變儀及其配套的反嚮壓力腔組件控製毛細管齣口壓力,在平均壓力為5 ~50 MPa下研究瞭3種不同特性黏度的聚酯(PET)的流變行為.結果錶明:PET的剪切黏度隨著平均壓力的增大都呈指數增加,符閤Barus方程.壓力繫數隨著特性黏度的增大而減小,噹特性黏度由0.48增加至0.67 dL/g時,壓力繫數顯著減小,且這種變化隨著剪切速率的增大而衰減,噹特性黏度≥0.67 dL/g時,壓力繫數隨剪切速率的變化不大.壓力繫數隨剪切速率的增大而減小,特性黏度為0.48 dL/g時變化顯著,噹特性黏度≥0.67 dL/g時,壓力繫數隨剪切速率的變化不大.壓力繫數隨著溫度的升高而減小,且變化率隨著溫度的升高顯著減小.不同特性黏度PET壓力繫數的變化錶明,特性黏度較低時,自由體積較大,錶現在玻璃化轉變溫度低,受壓力的影響顯著;噹特性黏度為0.67和1.00 dL/g時,自由體積的減小不再明顯,因此受壓力的影響也不再明顯.
채용모세관류변의급기배투적반향압력강조건공제모세관출구압력,재평균압력위5 ~50 MPa하연구료3충불동특성점도적취지(PET)적류변행위.결과표명:PET적전절점도수착평균압력적증대도정지수증가,부합Barus방정.압력계수수착특성점도적증대이감소,당특성점도유0.48증가지0.67 dL/g시,압력계수현저감소,차저충변화수착전절속솔적증대이쇠감,당특성점도≥0.67 dL/g시,압력계수수전절속솔적변화불대.압력계수수전절속솔적증대이감소,특성점도위0.48 dL/g시변화현저,당특성점도≥0.67 dL/g시,압력계수수전절속솔적변화불대.압력계수수착온도적승고이감소,차변화솔수착온도적승고현저감소.불동특성점도PET압력계수적변화표명,특성점도교저시,자유체적교대,표현재파리화전변온도저,수압력적영향현저;당특성점도위0.67화1.00 dL/g시,자유체적적감소불재명현,인차수압력적영향야불재명현.